PIC12F1822 MICROCHIP [Microchip Technology], PIC12F1822 Datasheet - Page 260

no-image

PIC12F1822

Manufacturer Part Number
PIC12F1822
Description
8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC12F1822-E/SN
Manufacturer:
ABILIS
Quantity:
15 400
Part Number:
PIC12F1822-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC12F1822-E/SN
0
Part Number:
PIC12F1822-I/MF
Manufacturer:
ALLEGRO
Quantity:
1 001
Part Number:
PIC12F1822-I/MF
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC12F1822-I/P
Manufacturer:
MICROCHIP
Quantity:
1 200
Part Number:
PIC12F1822-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC12F1822-I/SN
Manufacturer:
MICROCHIP
Quantity:
4 500
Part Number:
PIC12F1822-I/SN
Manufacturer:
MICROCHI
Quantity:
1 700
Part Number:
PIC12F1822-I/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC12F1822-I/SN
0
Company:
Part Number:
PIC12F1822-I/SN
Quantity:
30 000
Part Number:
PIC12F1822T-I/MF
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC12F1822T-I/SN
0
PIC12F/LF1822/16F/LF1823
24.6.5
A Repeated Start condition occurs when the RSEN bit
of the SSP1CON2 register is programmed high and the
Master state machine is no longer active. When the
RSEN bit is set, the SCL pin is asserted low. When the
SCL pin is sampled low, the Baud Rate Generator is
loaded and begins counting. The SDA pin is released
(brought high) for one Baud Rate Generator count
(T
SDA is sampled high, the SCL pin will be deasserted
(brought high). When SCL is sampled high, the Baud
Rate Generator is reloaded and begins counting. SDA
and SCL must be sampled high for one T
action is then followed by assertion of the SDA pin
(SDA = 0) for one T
asserted low. Following this, the RSEN bit of the
FIGURE 24-27:
DS41413A-page 260
BRG
). When the Baud Rate Generator times out, if
I
START CONDITION TIMING
2
C MASTER MODE REPEATED
BRG
REPEAT START CONDITION WAVEFORM
SDA
SCL
while SCL is high. SCL is
Write to SSP1CON2
occurs here
SDA = 1,
SCL (no change)
BRG
. This
Preliminary
T
BRG
SDA = 1,
SCL = 1
T
BRG
Repeated Start
SSP1CON2 register will be automatically cleared and
the Baud Rate Generator will not be reloaded, leaving
the SDA pin held low. As soon as a Start condition is
detected on the SDA and SCL pins, the S bit of the
SSP1STAT register will be set. The SSP1IF bit will not
be set until the Baud Rate Generator has timed out.
Sr
Note 1: If RSEN is programmed while any other
T
BRG
2: A bus collision during the Repeated Start
S bit set by hardware
At completion of Start bit,
hardware clears RSEN bit
Write to SSP1BUF occurs here
event is in progress, it will not take effect.
condition occurs if:
and sets SSP1IF
• SDA is sampled low when SCL
• SCL goes low before SDA is
T
BRG
goes from low-to-high.
asserted low. This may indicate that
another master is attempting to
transmit a data ‘1’.
1st bit
T
BRG
 2010 Microchip Technology Inc.

Related parts for PIC12F1822