KSZ8851-16MLLJ_10 MICREL [Micrel Semiconductor], KSZ8851-16MLLJ_10 Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
KSZ8851-16MLLJ_10
Manufacturer Part Number
KSZ8851-16MLLJ_10
Description
Single-Port Ethernet MAC Controller with 8-Bit or 16-Bit Non-PCI Interface
Manufacturer
MICREL [Micrel Semiconductor]
Datasheet
1.KSZ8851-16MLLJ_10.pdf
(90 pages)
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Power Modes, Power Supplies, and Packaging
•
•
•
•
•
•
•
March 2010
Micrel, Inc.
Integrated MAC and PHY Ethernet Controller fully
compliant with IEEE 802.3/802.3u standards
Designed for high performance and high throughput
applications
Supports 10BASE-T/100BASE-TX
Supports IEEE 802.3x full-duplex flow control and half-
duplex backpressure collision flow control
Supports DMA-slave burst data read and write
transfers
Supports IP Header (IPv4)/TCP/UDP/ICMP checksum
generation and checking
Supports IPv6 TCP/UDP/ICMP checksum generation
and checking
Automatic 32-bit CRC generation and checking
Simple SRAM-like host interface easily connects to
most common embedded MCUs.
Supports multiple data frames for transmit and receive
without address bus and byte-enable signals
Supports both Big- and Little-Endian processors
Larger internal memory with 12K Bytes for RX FIFO
and 6K Bytes for TX FIFO. Programmable low, high
and overrun watermark for flow control in RX FIFO
Shared data bus for Data, Address and Byte Enable
Efficient architecture design with configurable host
interrupt schemes to minimize host CPU overhead and
utilization
Powerful and flexible address filtering scheme
Optional to use external serial EEPROM configuration
for MAC address
Single 25MHz reference clock for both PHY and MAC
HBM ESD Rating 6kV
Single 3.3V power supply with options for 1.8V, 2.5V
and 3.3V VDD I/O
Built-in integrated 3.3V or 2.5V to 1.8V low noise
regulator (LDO) for core and analog blocks
Enhanced power management feature with energy
detect mode and soft power-down mode to ensure
low-power dissipation during device idle periods
Comprehensive LED indicator support for link, activity
and 10/100 speed (2 LEDs) - User programmable
Low-power CMOS design
Extended Temperature Range: –40°C to +125°C
Flexible package options available in 48-pin (7mm x
7mm) LQFP KSZ8851-16MLLJ or 128-pin PQFP
KSZ8851-16MQLJ
2
Additional Features
In addition to offering all of the features of a Layer 2
controller, the KSZ8851-16MLLJ offers:
•
•
•
•
•
•
Network Features
•
•
•
•
Applications
•
•
•
•
•
•
•
•
Markets
•
•
•
•
Flexible 8-bit and 16-bit generic host processor
interfaces with same access time and single bus
timing to any I/O registers and RX/TX FIFO buffers
Supports to add two-byte before frame header in order
for IP frame content with double word boundary
Micrel LinkMD® cable diagnostic capabilities to
determine cable length, diagnose faulty cables, and
determine distance to fault
Wake-on-LAN functionality
–
HP Auto MDI-X™ crossover with disable/enable option
Ability to transmit and receive frames up to 2000 bytes
10BASE-T and 100BASE-TX physical layer support
Auto-negotiation: 10/100 Mbps full and half duplex
Adaptive equalizer
Baseline wander correction
Video/Audio Distribution Systems
High-end Cable, Satellite, and IP set-top boxes
Video over IP and IPTV
Voice over IP (VoIP) and Analog Telephone Adapters
(ATA)
Industrial Control in Latency Critical Applications
Home Base Station with Ethernet Connection
Industrial Control Sensor Devices (Temperature,
Pressure, Levels, and Valves)
Security, Motion Control and Surveillance Cameras
Fast Ethernet
Embedded Ethernet
Industrial Ethernet
Embedded Systems
Incorporates Magic Packet™, wake-up frame,
network link state, and detection of energy signal
technology
M9999-030210-1.0
KSZ8851-16MLLJ