ICS1892 Integrated Circuit Systems, ICS1892 Datasheet - Page 39
![no-image](/images/no-image-200.jpg)
ICS1892
Manufacturer Part Number
ICS1892
Description
10Base-T/100Base-TX Integrated PHYceiver
Manufacturer
Integrated Circuit Systems
Datasheet
1.ICS1892.pdf
(148 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICS1892Y
Manufacturer:
ICS
Quantity:
20 000
- Current page: 39 of 148
- Download datasheet (817Kb)
7.2.5 Auto-Negotiation: Progress Monitor
ICS1892, Rev. D, 2/26/01
Under typical circumstances, the Auto-Negotiation sublayer can establish a connection with the ICS1892’s
remote link partner. However, some situations can prevent the auto-negotiation process from properly
achieving this goal. For these situations, the ICS1892 has an Auto-Negotiation Progress Monitor to provide
detailed status information to its Station Management (STA) entity. With this status information, the STA
can diagnose the failure mechanism and – in some situations – establish the link by correcting the problem.
When enabled, the auto-negotiation process typically requires less than 500 ms to execute, independent of
the link partner's ability to perform the auto-negotiation process. Typically, an STA polls both the
Auto-Negotiation Complete bit (bit 1.5) and the Link Status bit (bit 1.2) to determine when a link is
successfully established, either through auto-negotiation or parallel detection. The STA can then poll the
Auto-Negotiation Link Partner Ability Register and determine the highest-performance operating mode in
common with the capabilities it is advertising.
The ISO/IEC-defined priority table determines the established link type. As a simpler alternative, the STA
can read the QuickPoll Detailed Status Register and determine the link type from the Data Rate bit (bit
17.15) and the Duplex bit (bit 17.14). For convenience, the QuickPoll Register also includes the Link Status
bit (bit 17.0) and the Auto-Negotiation Complete bit (bit 17.4).
If (1) the auto-negotiation process does not complete, or (2) the link is not established, or (3) both the
auto-negotiation process does not complete and the link is not established, then the STA can determine the
cause of the link failure by using the outputs of the ICS1892 Auto-Negotiation Progress Monitor.
The Auto-Negotiation Progress Monitor provides the STA with four status bits of data to indicate both the
history and the present state of the auto-negotiation process. This status data is provided in the QuickPoll
Detailed Status register by using the Auto-Negotiation Complete bit (bit 17.4) as well as bits 17.13:11. The
bit order, from most-significant bit to least-significant bit, is 17.4, 17.13, 17.12, and 17.11. Using these four
bits, the Auto-Negotiation Progress Monitor provides nine state codes detailing the operation of the
auto-negotiation process for the STA. [For more information, see
Progress Monitor (bits
The nine Auto-Negotiation Progress Monitor state codes are 0h through 8h and Fh. The Auto-Negotiation
Progress Monitor automatically latches the values of the Auto-Negotiation Arbitration State Machine into
the status bits only if the value of the present state is greater than the value that is currently in the status
bits.
ICS1892
17.13:11)”.]
© 2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
39
Section 8.12.3, “Auto-Negotiation
Chapter 7 Functional Blocks
February 26, 2001
Related parts for ICS1892
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICM7101D](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7111](/images/no-image3.png)
Part Number:
Description:
Speech And Ringer Ic With Digital Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7102](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7115](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic With Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7102b](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7600](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Voltage Output Quad Dacs With Parallel Interface
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![AD583](/images/manufacturer_photos/0/0/56/analog_devices_tmb.jpg)
Part Number:
Description:
IC Sample and Hold Gated OP Amp
Manufacturer:
Analog Devices
Datasheet:
![ICM202B](/images/no-image3.png)
Part Number:
Description:
CIF/QCIF CMOS image sensor
Manufacturer:
IC Media
Datasheet:
![ICM7561](/images/no-image3.png)
Part Number:
Description:
(ICM7521 - ICM7561) 12/10/8-Bit Low Power Single DAC
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7562](/images/no-image3.png)
Part Number:
Description:
(ICM7522 - ICM7562) 12/10/8-Bit Low Power Dual DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7563](/images/no-image3.png)
Part Number:
Description:
(ICM7523 - ICM7563) 12/10/8-Bit Low Power Quad DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7521](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Single Dac With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7522](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Dual Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7523](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Quad Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7363](/images/no-image3.png)
Part Number:
Description:
Quad 12/10/8-bit Voltage-output Dacs
Manufacturer:
IC MICROSYSTEMS
Datasheet: