ICS1892 Integrated Circuit Systems, ICS1892 Datasheet - Page 25
ICS1892
Manufacturer Part Number
ICS1892
Description
10Base-T/100Base-TX Integrated PHYceiver
Manufacturer
Integrated Circuit Systems
Datasheet
1.ICS1892.pdf
(148 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICS1892Y
Manufacturer:
ICS
Quantity:
20 000
- Current page: 25 of 148
- Download datasheet (817Kb)
6.2 100M Symbol Interface
ICS1892, Rev. D, 2/26/01
The 100M Symbol Interface has a primary objective of supporting 100Base-TX repeater applications for
which the repeater requires only recovered parallel data and for which the repeater provides all the
necessary framing and control functions.
When the Mac/Repeater Interface is configured for 100M Symbol operations, the ICS1892 and the
MAC/repeater exchange unframed 5-bit, parallel symbols at a 25-MHz clock rate.
The ICS1892 configuration functions determine the operation of the MAC/Repeater Interface. The
configuration functions are controlled by either input pins (in which case, the HW/SW pin is logic zero to
select the hardware mode) or Management Register bits (in which case, the HW/SW pin is logic one to
select the software mode).
•
•
The 100M Symbol Interface bypasses the ICS1892 PCS and provides a direct unscrambled, unframed,
5-bit interface between the MAC/repeater and the PMA sublayer. A benefit of bypassing the PCS is a
reduction in the latency through the ICS1892. That is, when the ICS1892 MAC/Repeater Interface is
configured as a 100M Symbol Interface, the bit delays through the ICS1892 are smaller than the standard
MII Data Interface can allow. The ICS1892 provides this 100M Symbol Interface primarily for Repeater
applications, for which latency is a critical performance parameter.
In addition to the exchange of symbol data, the ICS1892 provides ISO/IEC-compliant control signals (such
as CRS) to the MAC/repeater. The ICS1892 CRS signal provides a fast look-ahead, which can benefit a
repeater application.
In the 100M Symbol Interface mode, the ICS1892 continues to assert the CRS signal using its PCS logic.
This action does not affect the bit delay or latency because the PCS CRS logic examines the bits received
from the PMA sublayer serially. In fact, because the PCS CRS does not wait for a nibble or symbol to be
constructed, the PCS CRS is available in advance of the symbol generation. Therefore, by employing the
PCS CRS generation logic, the ICS1892 can provide an ‘early’ indication of a Carrier Detect to the
MAC/repeater.
The 100M Symbol Interface consists of the following fourteen signals: STCLK, STD[4:0], SRCLK,
SRD[4:0], SCRS, and SD. (When the ICS1892 MAC/Repeater Interface is configured for 100M Symbol
operations, its default MII pin names and their associated functions are redefined. For more information,
see
Note:
In hardware mode, the ICS1892 enables the 100M Symbol Interface when both of the following are true:
In software mode, the ICS1892 enables the 100M Symbol Interface when both the following are true:
– The MII/SI input pin is logic one (that is, the selection is for the Symbol Interface).
– The 10/100SEL input pin is logic one (that is, the selection is for 100M operations).
– The MII/SI input pin is logic one (that is, the selection is for the Symbol Interface).
– The Control Register Data Rate bit (bit 0.13) is set to logic one (that is, the selection is for selecting
ICS1892
Section 9.2.4.2, “MAC/Repeater Interface Pins for 100M Symbol
100M operations)
In software mode, the 10/100SEL pin becomes an output that indicates the state of bit 0.13.
© 2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
25
Interface”.)
Chapter 6 Interface Overviews
February 26, 2001
Related parts for ICS1892
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Speech And Ringer Ic With Digital Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Low Cost Single Chip Telephone Ic With Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
12/10/8-bit Low Power Voltage Output Quad Dacs With Parallel Interface
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
IC Sample and Hold Gated OP Amp
Manufacturer:
Analog Devices
Datasheet:
Part Number:
Description:
CIF/QCIF CMOS image sensor
Manufacturer:
IC Media
Datasheet:
Part Number:
Description:
(ICM7521 - ICM7561) 12/10/8-Bit Low Power Single DAC
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
(ICM7522 - ICM7562) 12/10/8-Bit Low Power Dual DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
(ICM7523 - ICM7563) 12/10/8-Bit Low Power Quad DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
12/10/8-bit Low Power Single Dac With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
12/10/8-bit Low Power Dual Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
12/10/8-bit Low Power Quad Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
Part Number:
Description:
Quad 12/10/8-bit Voltage-output Dacs
Manufacturer:
IC MICROSYSTEMS
Datasheet: