DS26303G-120 MAXIM [Maxim Integrated Products], DS26303G-120 Datasheet - Page 69
DS26303G-120
Manufacturer Part Number
DS26303G-120
Description
3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.DS26303G-120.pdf
(97 pages)
- Current page: 69 of 97
- Download datasheet (2Mb)
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
are all 0s. When a new pattern is loaded, the pattern generator is loaded with a seed/pattern value before pattern
n
generation starts. The seed/pattern value is programmable (0 – 2
– 1).
6.9.3.1
Transmit Error Insertion
Error insertion inserts errors into the outgoing pattern data stream. Errors are inserted one at a time or at a rate of
n
one out of every 10
bits. The value of n is programmable (1 to 7 or off). Single bit-error insertion can be initiated
from the microprocessor interface, or by the manual error-insertion input (TMEI). The method of single error
insertion is programmable (register or input). If pattern inversion is enabled, the data stream is inverted before the
overhead/stuff bits are inserted. Pattern inversion is programmable (on or off).
6.10 Special Test Functions
This section is used for designer notes. Any special features or test functions that are for internal use or possible
future features that may be needed should be documented here.
6.10.1 Metal Options
The DS26303 has a metal option to allow for pins D0 to D7 to be metal revised. The metal revision adds VDDIO/2
pullup and pulldown to pins D0 to D7. This has been added in case compatibility in hardware mode needs to match
the LXT384 part.
69 of 97
Related parts for DS26303G-120
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Buffers & Line Drivers 3.3V E1/T1/J1 Short Haul Octal LIU
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TYPE DS FUSED DISCONNECT SWITCH 60A 3P
Manufacturer:
EATON CUTLER HAMMER
Part Number:
Description:
LCC/M°/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products