SI3452 SILABS [Silicon Laboratories], SI3452 Datasheet - Page 19
![no-image](/images/no-image-200.jpg)
SI3452
Manufacturer Part Number
SI3452
Description
QUAD HIGH-VOLTAGE PORT CONTROLLER FOR POE AND POE+ PSES
Manufacturer
SILABS [Silicon Laboratories]
Datasheet
1.SI3452.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3452-B01-GM
Manufacturer:
SILICON
Quantity:
1 000
Company:
Part Number:
SI3452-B02-GM
Manufacturer:
AD
Quantity:
556
Part Number:
SI3452-B02-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
SI3452-B02-GMR
Manufacturer:
TI
Quantity:
1 001
Company:
Part Number:
SI3452A-B01-GM
Manufacturer:
SILICON
Quantity:
1 001
Company:
Part Number:
SI3452A-B01-GMR
Manufacturer:
SILICON
Quantity:
670
Part Number:
SI3452B-B02-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
SI3452C-B02-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
5.5. Command and Return Registers (Registers 0x12–0x1C)
The global command register enables manual port turn-on or turn-off, chip reset, port reset, and measurement of
port current and V
commands.
If the command results in a numerical return value, that value is stored in the measurement registers, which are
read-only. Each of the five possible measurements results in a 2 byte return value, and that value is stored in a
unique register. V
full scale is 6.5535 A.
The output data is updated by the proper command register write operation (see Table 23). This means that the
numerical value of the port current or V
command was issued. If the port turns off due to an overload or disconnect, the port current register contents will
not be set to zero. If a command to read port current is issued and the port is off, the return value will be zero.
5.6. Device Status Register (0x1D)
The device event bits are listed in Table 18.
The Device status register is RO. The V
or temperature is out of range and reset if the V
there is a change in the overtemp status (bit 6 of 0x1D), and bit 5 of the Interrupt register is set if there is a change
in the V
not clear the device status register.
In addition, bit B0 indicates whether or not detection back-off is used. For PSEs that are wired as Alternative B
(power on the spare pair–typically used for midspans), the time between detection pulses is increased to slightly
over two seconds to avoid interference with Alternative A (power on the data pair–typically used for endpoints). Bit
B0 can be toggled using the 0x10 command code.
B6 - OverTemp
B5 - V
EE
UVLO status (bit 5 of 0x1D). Reading register 0x1D clears these bits of the Interrupt register but does
Bit
EE
UVLO
EE
EE
is encoded in mV units; so, the full scale is 65.535 V. Iport is encoded in 100 µA units; so, the
. Register 0x12 is a Write only register. See Table 24 on page 23 for a list of all available
The Si3452/3 has per-port thermal shutdown sensors as well a global thermal shutdown
at a slightly higher temperature. The global thermal shutdown bit of the device event
register is set if this occurs.
V
EE
UVLO. The part is put in its reset state if V
EE
EE
Table 18. Device Status Bits
, UVLO, and overtemp bits reflect the device status. They are set if V
voltage in the measurement register will be the value at the time the
EE
or temperature is in range. Bit 6 of the Interrupt register is set if
Rev. 1.0
Description
EE
is not in a valid range.
Si3452/3
EE
19