SI3452 SILABS [Silicon Laboratories], SI3452 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
SI3452
Manufacturer Part Number
SI3452
Description
QUAD HIGH-VOLTAGE PORT CONTROLLER FOR POE AND POE+ PSES
Manufacturer
SILABS [Silicon Laboratories]
Datasheet
1.SI3452.pdf
(36 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3452-B01-GM
Manufacturer:
SILICON
Quantity:
1 000
Company:
Part Number:
SI3452-B02-GM
Manufacturer:
AD
Quantity:
556
Part Number:
SI3452-B02-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
SI3452-B02-GMR
Manufacturer:
TI
Quantity:
1 001
Company:
Part Number:
SI3452A-B01-GM
Manufacturer:
SILICON
Quantity:
1 001
Company:
Part Number:
SI3452A-B01-GMR
Manufacturer:
SILICON
Quantity:
670
Part Number:
SI3452B-B02-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
SI3452C-B02-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Si3452/3
4.4. Disconnect Detection
4.4.1. dV/dt Disconnect (Si3452)
The dV/dt disconnect function can be used to detect a disconnected device without using dc disconnect or ac
disconnect.
In dV/dt disconnect mode, the FET current limit is switched to 7.5 mA. If the voltage across the FET increases, a
load is assumed to be present, and the FET current limit is automatically switched back to its pre-selected value. If,
after 350 ms, the FET voltage has not increased, there is no load present, and the FET is turned off.
In addition to operating in a manner functionally distinct from DC disconnect, dV/dt disconnect requires no
additional external components and fully interoperates with all powered device DC Maintain Power Signatures. For
more information, see "AN399: dV/dt Disconnect and the IEEE 802.3 PoE Standard".
4.4.2. DC Disconnect (Si3453)
The port current is continuously monitored by the Si3452/3. The Si3452/3 can dynamically change the
measurement scale to achieve accuracy over a wide range of currents.
As defined in the IEEE 802.3 PoE standard, the PSE should disconnect if the port current is less than a nominal
7.5 mA for more than 350 ms.
4.5. Transient Voltage Surge Suppression
The Si3452/3 features robust on-chip surge protectors on each port; this is an industry first. This unique protection
circuitry acts as an active device that can withstand lightning-induced transients as well as large ESD transient
events. When the port voltage exceeds its protection limit and the current reaches a triggering threshold, current is
shunted from the port to the ground pins.
Internal circuitry is provided to protect the line outputs from externally-coupled fault currents. These are transient
currents of up to 5 A peak.
The operation of the protection circuits depends on the operating mode of the channel switch and the direction of
the fault current. The clamping operation is performed on the detect pin.
The switch itself will also be protected by the current limit. If the transient lasts long enough to heat up the die, then
the temperature sense circuit will shut off the switch, and all the fault current will flow through the clamp diode.
4.6. Temperature Sense
A temperature sense signal is used in conjunction with the current limit status signals from the gate drive blocks.
Any channel that is generating excess heat is assumed to be operating in current limit mode, with both high voltage
drop and high current.
If the port is in PoE mode, an overload will generally not result in thermal shutdown before the 60 ms I
the port is in PoE+ mode, an overload may cause the port to shut down prior to the 60 ms I
case, the event is reported as I
by the 802.3at draft and provides much more robust overload protection than is possible with external FETs.
In addition, there is a thermal shutdown if the package temperature exceeds 120 °C. If this threshold is reached, all
output drivers are turned off and detection modes are disabled. This secondary threshold limit guards against the
possibility that the overheating is not caused by a driver operating in current limit.
4.7. Port Measurement and Monitoring
VEE monitoring in conjunction with port current monitoring allows measurement of port power. Port power
monitoring, dynamic power allocation via LLDP*, and port power policing allow efficient power supply sizing.
The Si3452/3 is factory-calibrated and temperature-compensated for the following measurements:
*Note: LLDP = Link Layer Discovery Protocol. Refer to IEEE 802.3at (draft) and IEEE 802.1AB for more information.
14
Port current measurement. These measurements are auto-ranged and scaled to a 16 bit number at 100 µA per
bit. Port current accuracy is ±4% ± 2 mA.
V
V
EE
EE
is measured with a scale of 64 V. The measurement is reported as a 16-bit number scaled at 1 mV per bit.
measurement accuracy is ±4% over the valid V
CUT
. The faster shutdown in PoE+ mode is consistent with and specifically allowed
Rev. 1.0
EE
range.
CUT
period. In either
CUT
period. If