xr16l651im Exar Corporation, xr16l651im Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16l651im
Manufacturer Part Number
xr16l651im
Description
2.25v To 5.5v Uart With 32-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16L651IM.pdf
(56 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16l651im-F
Manufacturer:
Exar Corporation
Quantity:
10 000
XR16L651
2.25V TO 5.5V UART WITH 32-BYTE FIFO
XFR [4]: Xon-Any Enable
This bit enables and disables the Xon-Any function when Xon/Xoff software flow control is enabled.
XFR [5]: Invert Auto RS-485 Control Output
When Auto RS485 feature is enabled, XFR[2]=1, RTS# output automatically changes its logic state to control
the RS-485 transceiver.
XFR [7:6]: Reserved
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
MSR[0]: Delta CTS# Input Flag
MSR[1]: Delta DSR# Input Flag
MSR[2]: Delta RI# Input Flag
MSR[3]: Delta CD# Input Flag
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS (EFR bit-7). Auto CTS flow control allows starting and stopping of local data transmissions based on the
modem CTS# signal. A logic 1 on the CTS# pin will stop UART transmitter as soon as the current character
has finished transmission, and a logic 0 will resume data transmission. Normally MSR bit-4 bit is the
compliment of the CTS# input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR
register. The CTS# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
DSR# (active high, logical 1). Normally this bit is the compliment of the DSR# input. In the loopback mode, this
bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a general purpose input
when the modem interface is not used.
4.10
Logic 0 = Disable the Xon-Any function.
Logic 1 = Enable the Xon-Any function. The receiver will use any received character as an Xon character
and resume data transmission.
Logic 0 = During auto RS-485, RTS# control output signal to the transceiver is logic 1 for transmit and logic 0
for receive.
Logic 1 = The RTS# output control signal to the transceiver is logic 0 for transmit and logic 1 for receive. User
must assert RTS# for operation to take effect.
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3).
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
Modem Status Register (MSR) - Read Only
34
áç
áç
áç
áç
REV. 1.3.0