atmega161-4pi ATMEL Corporation, atmega161-4pi Datasheet - Page 123
atmega161-4pi
Manufacturer Part Number
atmega161-4pi
Description
8-bit Microcontroller With 16k Bytes Of In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATMEGA161-4PI.pdf
(159 pages)
- Current page: 123 of 159
- Download datasheet (2Mb)
Reading the Flash
Reading the EEPROM
Programming the Fuse Bits
Programming the Lock Bits
1228D–AVR–02/07
The algorithm for reading the Flash memory is as follows (refer to “Programming the
Flash” on page 120 for details on command and address loading):
1. A: Load Command “0000 0010”.
2. H: Load Address High Byte ($00 - $1F)
3. B: Load Address Low Byte ($00 - $FF)
4. Set OE to “0”, and BS1 to “0”. The Flash word Low byte can now be read at
5. Set BS to “1”. The Flash word High byte can now be read at DATA.
6. Set OE to “1”.
The algorithm for reading the EEPROM memory is as follows (refer to “Programming the
Flash” on page 120 for details on command and address loading):
1. A: Load Command “0000 0011”.
2. H: Load Address High Byte ($00 - $01)
3. B: Load Address ($00 - $FF)
4. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at
5. Set OE to “1”.
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” on page 120 for details on command and data loading):
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Give WR a negative pulse and wait for RDY/BSY to go high.
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” on page 120 for details on command and data loading):
1. A: Load Command “0010 0000”.
2. D: Load Data Low Byte. Bit n = “0” programs the Lock bit.
3. L: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
DATA.
DATA.
Bit 6 = BOOTRST Fuse bit
Bit 5 = SPIEN Fuse bit
Bit 4 = SUT Fuse bit
Bit 3 = “1”. This bit is reserved and must be left unprogrammed (“1”).
Bits 2 - 0 = CKSEL2..0 Fuse bits
Bit 7 = “1”. This bit is reserved and should be left unprogrammed (“1”).
Bit 5 = Boot Lock Bit12
Bit 4 = Boot Lock Bit11
Bit 3 = Boot Lock Bit02
Bit 2 = Boot Lock Bit01
Bit 1 = Lock Bit2
Bit 0 = Lock Bit1
Bits 7 - 6 = “1”. These bits are reserved and should be left unprogrammed (“1”).
ATmega161(L)
123
Related parts for atmega161-4pi
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: