w25q16bv Winbond Electronics Corp America, w25q16bv Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
w25q16bv
Manufacturer Part Number
w25q16bv
Description
16m-bit Serial Flash Memory With Dual And Quad Spi
Manufacturer
Winbond Electronics Corp America
Datasheet
1.W25Q16BV.pdf
(65 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
w25q16bvCC3
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Part Number:
w25q16bvFCC3
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Company:
Part Number:
w25q16bvIG
Manufacturer:
WINBOND
Quantity:
10 549
Part Number:
w25q16bvNIG
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Company:
Part Number:
w25q16bvSIG
Manufacturer:
JMICRON
Quantity:
1 000
Part Number:
w25q16bvSIG
Manufacturer:
WINOND
Quantity:
20 000
Company:
Part Number:
w25q16bvSS1G
Manufacturer:
SemiHow
Quantity:
16 000
Company:
Part Number:
w25q16bvSSIG
Manufacturer:
WINBOND
Quantity:
9 270
Company:
Part Number:
w25q16bvSSIG
Manufacturer:
WINBOND
Quantity:
20 655
Part Number:
w25q16bvSSIG
Manufacturer:
WINBOND/华邦
Quantity:
20 000
9. FUNCTIONAL DESCRIPTION
9.1
9.1.1
The W25Q16BV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising edges of /CS.
9.1.2
The W25Q16BV supports Dual SPI operation when using the “Fast Read Dual Output and Dual I/O” (3B
and BB hex) instructions. These instructions allow data to be transferred to or from the device at two to
three times the rate of ordinary Serial Flash devices. The Dual Read instructions are ideal for quickly
downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical code
directly from the SPI bus (XIP). When using Dual SPI instructions the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
9.1.3
The W25Q16BV supports Quad SPI operation when using the “Fast Read Quad Output”, “Fast Read
Quad I/O”, “Word Read Quad I/O” and “Octal Word Quad I/O” (6B, EB, E7 and E3 hex respectively).
These instructions allow data to be transferred to or from the device four to six times the rate of ordinary
Serial Flash. The Quad Read instructions offer a significant improvement in continuous and random
access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP).
When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP
and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad
Enable bit (QE) in Status Register-2 to be set.
9.1.4
The /HOLD signal allows the W25Q16BV operation to be paused while it is actively selected (when /CS is
low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared with
other devices. For example, consider if the page buffer was only partially written when a priority interrupt
requires use of the SPI bus. In this case the /HOLD function can save the state of the instruction and the
data in the buffer so programming can resume where it left off once the bus is available again. The
/HOLD function is only available for standard SPI and Dual SPI operation, not during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to avoid
resetting the internal logic state of the device.
SPI OPERATIONS
Standard SPI Instructions
Dual SPI Instructions
Quad SPI Instructions
Hold Function
- 10 -
W25Q16BV