zpsd211r STMicroelectronics, zpsd211r Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
zpsd211r
Manufacturer Part Number
zpsd211r
Description
Low Cost Field Programmable Microcontroller Peripherals
Manufacturer
STMicroelectronics
Datasheet
1.ZPSD211R.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
zpsd211r-B-15
Manufacturer:
ST/WSI
Quantity:
20 000
Company:
Part Number:
zpsd211r-B-15J
Manufacturer:
ZILOG
Quantity:
34
Company:
Part Number:
zpsd211r-B-90JI
Manufacturer:
WSi
Quantity:
2
Company:
Part Number:
zpsd211rV-A-20J
Manufacturer:
WSI
Quantity:
132
Company:
Part Number:
zpsd211rV-B-25J
Manufacturer:
TEXAS
Quantity:
175
Table 2.
PSD211R Pin
Descriptions
Legend:
R/W/V
A19/CSI
WR/V
ALE/AS
Name
PSEN
Reset
RD/E
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
or
PP
PP
The Type column abbreviations are: I = input only; I/O = input/output; P = power.
Type
I/O
I/O
I
I
I
I
I
I
This pin is for 8031 or compatible MCUs that use PSEN to
separate program space from data space. In this case, PSEN is
used for reads from the EPROM.
Notes:
1) If your MCU does not output a PSEN signal, pull up this pin to
2) In programming mode, this pin is pulsed between V
The following control signals can be connected to this port, based on
your MCU (and the way you configure the PSD in PSDsoft):
1. WR—active-low write pulse.
2. R/W—active-high read/active-low write input.
Note: in programming mode, this pin must be tied to V
The following control signals can be connected to this port, based on
your MCU (and the way you configure the PSD in PSDsoft):
1. RD—active-low read input.
2. E—E clock input.
The following control signals can be connected to this port:
1. CSI-Active-low chip select input. If your MCU supports a chip
2. If you don’t wish to use the CSI feature, you may use this pin as
PSD211R/ZPSD211R:
This pin is user-programmable and can be configured to reset on a
high- or low-level input. Reset must be applied for at least 100 ns.
ZPSD211RV:
This pin is not configurable, and the chip will only reset on an
active-low level input. Reset must be applied for at least 500 ns,
and no operations may take place for an additional 500 ns minimum.
(See Figure 8.)
Connect ALE or AS to this pin. The polarity of this pin is configurable.
The trailing edge of ALE/AS latches all multiplexed address inputs.
These pins make up Port A. These port pins are configurable, and
can have the following functions: (see Figure 5)
1. MCU I/O—in this mode, the direction of the pin is defined by its
2. Latched address output.
These pins make up Port B. These port pins are configurable, and
can have the following functions: (see Figure 6)
1. MCU I/O —in this mode, the direction of the pin is defined by its
2. Chip select output —each of PB0-3 has four product terms
V
direction bit, which resides in the direction register.
direction bit, which resides in the direction register.
available per pin, while PB4-7 have 2 product terms each.
See Figure 4.
select output, and you want the PSD to save power when not
selected, use this pin as a chip select input.
an additional input (logic or address) to the PAD. A19 can be
latched with ALE/AS, or be a transparent logic input.
CC
.
Description
PP
PSD211R Family
PP
and 0 V.
.
7