pxb4219 Infineon Technologies Corporation, pxb4219 Datasheet - Page 59
pxb4219
Manufacturer Part Number
pxb4219
Description
Iwe8 Interworking Element For 8 E1/t1 Lines
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PXB4219.pdf
(290 pages)
- Current page: 59 of 290
- Download datasheet (4Mb)
Table 17
ATM Adaptation
Layer Type
AAL0
AAL1
AAL1 with CAS
1)
2)
4.3.2
In “Inactive” mode, no data is accepted from the framer receive interface.
In “Active” mode, data is accepted from the framer receive interface, segmented and
cells are written into the Segmentation Buffers and the Output Queue.
In “Standby” mode, data is accepted from the framer receive interface but no cells are
written in the Segmentation Buffers.
In “Substitute” mode, data is accepted from the framer receive interface, but substituted
by a programmable byte-pattern selected by “subst_bpslct” in the “AAL Receive
Reference Slot”. Cells are written into the Segmentation Buffers and the Output Queue.
This mode can be used for trunc conditioning to indicate idle (bit pattern = Ox7F) or out-
of-service conditions (bit pattern = Ox1A) according to af-vtoa-0078 [10] and TR-NWT-
000170 [14]
When activating the AAL segmentation channels, it is important to follow the initialization
sequence as shown in
the AAL channel. During this time the device connected to the Framer Receive Interface
has to be in normal operation allowing the IWE8 to synchronize itself on the frame pulse.
Table 18
Step
1
2
3
The RTS value stored in the RTS buffer of the port is loaded from the Internal Clock
Recovery Circuit ICRC or from the Clock Recovery Interface. A new value will be
Data Sheet
P format, cell may have only 46 user data octets in non-P format
Cb: Required bytes for the CAS subblock in an ATM cell = RoundUp(N/2)
pcfN
p_rx_act
0 = inactive
1 = active
1 = active
Setup of AAL Segmentation Channels
Cell Filling level values
Activation sequence for AAL segmentation channels
Table
Minimum
4
4
4+Cb
AAL Receive Reference Slot.
channel_mode
00 = Inactive
00 = Inactive
01 or 11 = Active
18. Step 2 must be held at least 250 µ s to internally reset
2)
Partially Filled
Maximum
47
46
46
59
PXB4219 / PXB4220 / PXB4221
Completely Filled
48
47
47
1)
1)
Operational Description
Minimum Time
250 µ s
2002-05-06
Related parts for pxb4219
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: