peb20534 Infineon Technologies Corporation, peb20534 Datasheet - Page 76
peb20534
Manufacturer Part Number
peb20534
Description
Dma Supported Serial Communication Controller With 4 Channels
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PEB20534.pdf
(439 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
peb20534H-10-V2.1
Manufacturer:
INF
Quantity:
5 510
Company:
Part Number:
peb20534H-10-V2.1
Manufacturer:
PHILIPS
Quantity:
5 510
Company:
Part Number:
peb20534H-10V2.1
Manufacturer:
MICRON
Quantity:
78
Company:
Part Number:
peb20534H-52V2.0
Manufacturer:
SIEMENS
Quantity:
5 510
Company:
Part Number:
peb20534H-52V2.0
Manufacturer:
SIEMENS
Quantity:
5 510
Company:
Part Number:
peb20534H10-V21
Manufacturer:
Infineon Technologies
Quantity:
10 000
Company:
Part Number:
peb20534H52-V2.1
Manufacturer:
Infineon Technologies
Quantity:
10 000
- Current page: 76 of 439
- Download datasheet (6Mb)
5.1.2.3
This mode is selected by setting bit CMODE=’0’ in register GMODE (see
Global Mode Register” on Page
The DMA controller operates on linked lists with pointer information stored in the DSCC4
internal configuration section.
The software starts DMAC operation by writing the action request bit ’AR’ in the Global
Command Register (GCMDR). On this command, the DMAC checks all channel specific
Configuration registers CHiCFG for initialization command bits (’IDR’, ’IDT’).
Each DMA channel which is triggered for initialization by one of the above mentioned
commands fetches the Base Transmit/Receive Descriptor Address (BTDA/BRDA) from
its CHiBTDA/CHiBRDA register. The DMA channel continues reading the Tx/Rx
descriptors from the shared memory which in turn point to the associated data buffer and
the next descriptor address.
The external memory associated to a DMA channel is organized as a chained list of
buffers (typically 256 bytes) set up by an external host. Each chained list is composed of
descriptors and data sections. The descriptor contains the pointer to the next descriptor,
the start address of the data buffer and the size of a data section. In transmit direction
the data pointer is a byte address. The descriptor also includes control information like
frame end (frame end for HDLC modes, block end indication for ASYNC and extended
transparent mode), transmission hold and host initiated interrupt.
Transmit:
• In transmit direction the DMA controller reads a transmit descriptor, calculates the
Data Sheet
data address and fills the DSCC4 central transmit FIFO. When the data transfer of the
specified section is completed, the DMA controller marks the buffer as “completed”
and branches off to the next transmit descriptor. If a frame end (FE) is indicated in the
buffer descriptor (HDLC and block oriented protocol modes), a frame end indication is
forwarded to the serial channel after the data has been transferred, and the frame will
be closed correctly by the SCC. A maskable interrupt status may be generated at the
completion of transmission to be stored in the interrupt queue by the interrupt
controller. Transmission of another frame can begin immediately.
However, if the current transmit buffer descriptor has its “HOLD” bit set, the DMA
channel does not branch off to the next descriptor. If no frame end was encountered
in the current descriptor, an active “HOLD” bit causes a transmit FIFO underrun to
occur, and a frame to be aborted by the serial channel.
Furthermore an error interrupt is generated anytime a transmit channel detects the
HOLD condition without a frame end indication asserted.
Once, the DSCC4 has sensed the HOLD=’1’ condition in transmit direction, the data
transfer can be restarted by a single poll command (GCMDR:TXPOLLi=1; i=0...3) or
by setting the ’AR’ bit in the GCMDR register after the configuration register has been
updated for the corresponding channel (new channel initialization). The transmit poll
command causes the channel to read the HOLD bit (first DWORD of the descriptor)
DMAC Operation Using Hold-Bit Control Mechanism
241).
76
DMA Controller and Central FIFOs
PEB 20534
PEF 20534
“GMODE:
2000-05-30
Related parts for peb20534
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: