isp1761 NXP Semiconductors, isp1761 Datasheet - Page 94

no-image

isp1761

Manufacturer Part Number
isp1761
Description
Hi-speed Universal Serial Bus On-the-go Controller
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
isp1761BE
Manufacturer:
ST
0
Part Number:
isp1761BE
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
isp1761BE
Quantity:
56
Company:
Part Number:
isp1761BE
Quantity:
1 000
Part Number:
isp1761BE-S
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
isp1761BEGE
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
isp1761BEUM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
isp1761ET
Manufacturer:
NXP
Quantity:
853
Part Number:
isp1761ET
Manufacturer:
ST
0
Part Number:
isp1761ET
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
NXP Semiconductors
Table 86.
[1]
ISP1761_4
Product data sheet
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
The reset value depends on the corresponding OTG status. For details, see
OTG Status register (address 0378h) bit allocation
9.5.3.1 OTG Status register
B_SESS_
9.5.3 OTG Interrupt registers
END
15
[1]
R
R
0
7
Table 85.
[1]
This register indicates the current state of the signals that can generate an interrupt. The
bit allocation of the register is given in
Table 87.
Bit
2
1
0
Bit
15 to 9
8
[1]
To use port 1 as a Host Controller, write 0080 0018h to this register after power-on. To use port 1 as a
Peripheral Controller, write 0006 0400h to this register after power-on.
14
R
R
0
6
0
Symbol
DM_PULLDOWN DM pull-down:
DP_PULLDOWN
DP_PULLUP
reserved
OTG Control register (address set: 0374h, clear: 0376h) bit description
OTG Status register (address 0378h) bit description
Symbol
-
B_SE0_SRP
13
R
R
0
5
0
Rev. 04 — 5 March 2007
Description
0 — Disable
1 — Enable
DP pull-down:
0 — Disable
1 — Enable
0 — The pull-up resistor is disconnected from the DP line. The data
line pulsing is stopped.
1 — An internal 1.5 k pull-up resistor is present on the DP line.
The data line pulsing is started.
Remark: When port 1 is in peripheral mode or it plays the role of a
peripheral while the OTG functionality is enabled, it depends on the
setting of DP_PULLUP and the V
DP line to HIGH through a pull-up resister. V
When 5 V is present on the V
reserved
Description
reserved for future use
2 ms of SE0 detected in the B-idle state
CONN
RMT_
12
R
R
0
4
0
Table
Table
86.
11
ID
[1]
R
R
0
3
87.
BUS
DP_SRP
10
BUS
R
R
pin, V
0
2
0
Hi-Speed USB OTG controller
sensing signal to connect the
BUS
A_B_SESS
= 1.
BUS
_VLD
[1]
R
R
9
0
1
is an internal signal.
© NXP B.V. 2007. All rights reserved.
ISP1761
VBUS_VLD
…continued
B_SE0_
SRP
94 of 163
[1]
R
R
8
0
0

Related parts for isp1761