adav400kstz-reel Analog Devices, Inc., adav400kstz-reel Datasheet - Page 33
![no-image](/images/no-image-200.jpg)
adav400kstz-reel
Manufacturer Part Number
adav400kstz-reel
Description
Audio Codec With Embedded Sigmadsp Processor
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADAV400KSTZ-REEL.pdf
(36 pages)
Table 27 can also be used to verify register settings for each
serial data format.
SRC SERIAL PORT CONTROL REGISTER
SRC Serial Input Port Select (Bits [6:5])
These bits select which of the four serial data inputs are directed
to the SRC.
LRCLK Polarity (Bit 4)
When this bit is set to 0, the left channel data on the selected
channel is clocked in when LRCLK0 is low, and the right
channel input data is clocked in when LRCLK1 is high. When
this bit is set to 1, this sequence is reversed.
BCLK Polarity (Bit 3)
This bit controls on which edge of the bit clock the input data
changes and on which edge it is clocked. Data changes on the
falling edge of BCLK0 when this bit is set to 0, and on the rising
edge when this bit is set to 1.
Serial Input Mode (Bits [2:0])
These two bits control the data format that the input port expects
to receive. It should be noted that Bit 3 and Bit 4 of the serial input
control register will override these settings, so Bits 4 to Bit 0
must be set for correct operation. Refer to
Figure 33, and Figure 34 for details on the different modes.
Table 27 can also be used to verify register settings for each
serial data format.
Note that TDM is not supported on the SRC.
ADC INPUT MUX REGISTER
ADC Input Mux (Bits [3:0])
These bits are used to select which of the analog inputs are
directed to the ADC. It is recommended that only one channel
is selected at any time.
POWER CONTROL REGISTER
Power Control (Bits [15:0])
These bits can individually power up or power down the blocks
of the ADAV400.
USER CONTROL REGISTER 2
Headphone Amplifier Mute (Bit 7)
When set, this bit mutes the analog headphone amplifier.
Figure 31, Figure 32,
Rev. A | Page 33 of 36
Headphone Amplifier Attenuation (Bits [4:0])
These bits set the analog gain of the headphone amplifier. It can
be set in steps of −1.5 dB from 0 dB to −46.5 dB.
USER CONTROL REGISTER 1
SRC Mux Enable (Bit 8)
When this bit is set to 1, the SRC mux is enabled, passing the
input selected by the SRC serial port control register to the SRC
block, the output of which is then available to the DSP core. It
also masks the selected serial data input as a direct input to the
DSP core. See
configuration.
SRC Lock Indicator (Bit 7)
This bit is read only and indicates when the SRC is locked.
MCLKO Pin Enable (Bit 6)
With this bit set to 1, MCLKO is enabled and outputs the
frequency selected by Bit 5 to Bit 3 in this register.
MCLKO Select (Bits [5:3])
These bits select the MCLKO frequency. All reserved settings
are test modes and are not valid audio clocks.
PLL Clock Select (Bits [2:0])
These bits must be programmed to select the master clock,
MCLKI, input frequency that is being used. For example, the
default case is 64 × f
can also be used as the MCLKI.
DAC AMPLIFIER REGISTER
DAC Amplifier Chopping (Bit 4)
This bit should be set to 1 to ensure best performance on the
headphone outputs.
LRCLK0
BCLK0
SDIN0
SDIN1
SDIN2
SDIN3
REG: 0x1056
BITS [6:5]
Figure 36 for more details on the SRC input
Figure 36. SRC Input Configuration
S
(3.072 MHz), which means that BCLKx
MULTICHANNEL
DIGITAL INPUTS
SRC
REG: 0x1058
PU
BIT 2
PROCESSOR
AUDIO
CORE
ADAV400