ics9lprs365 Integrated Device Technology, ics9lprs365 Datasheet - Page 2

• Manufacturer Part Number: ics9lprs365
• Description: 64-pin Ck505 W/fully Integrated Voltage Regulator + Integrated Series Resistor
• Manufacturer: Integrated Device Technology

TSSOP Pin Description
1218—09/01/10
PIN #
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
PCI0/CR#_A
VDDPCI
PCI1/CR#_B
PCI2/TME
PCI3
PCI4/27_Select
PCI_F5/ITP_EN
GNDPCI
VDD48
USB_48MHz/FSLA
GND48
VDD96_IO
DOTT_96/SRCT0
DOTC_96/SRCC0
GND
VDD
PIN NAME
TYPE
PWR
OUT
PWR
PWR
PWR
PWR
OUT
OUT
PWR
PWR
I/O
I/O
I/O
I/O
I/O
I/O
3.3V PCI clock output or Clock Request control A for either SRC0 or SRC2 pair
The power-up default is PCI0 output, but this pin may also be used as a Clock Request control of SRC pair
0 or SRC pair 2 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI output must first
be disabled in byte 2, bit 0 of SMBus address space . After the PCI output is disabled (high-Z), the pin can
then be set to serve as a Clock Request pin for either SRC pair 2 or pair 0 using the CR#_A_EN bit
located in byte 5 of SMBUs address space.
Byte 5, bit 7
0 = PCI0 enabled (default)
1= CR#_A enabled. Byte 5, bit 6 controls whether CR#_A controls SRC0 or SRC2 pair
0 = CR#_A controls SRC0 pair (default),
1= CR#_A controls SRC2 pair
Power supply pin for the PCI outputs, 3.3V nominal
3.3V PCI clock output/Clock Request control B for either SRC1 or SRC4 pair
The power-up default is PCI1 output, but this pin may also be used as a Clock Request control of SRC pair
1 or SRC pair 4 via SMBus. Before configuring this pin as a Clock Request Pin, the PCI output must first
be disabled in byte 2, bit 1 of SMBus address space . After the PCI output is disabled (high-Z), the pin can
then be set to serve as a Clock Request pin for either SRC pair 1 or pair 4 using the CR#_B_EN bit
located in byte 5 of SMBUs address space.
Byte 5, bit 5
0 = PCI1 enabled (default)
1= CR#_B enabled. Byte 5, bit 6 controls whether CR#_B controls SRC1 or SRC4 pair
Byte 5, bit 4
0 = CR#_B controls SRC1 pair (default)
1= CR#_B controls SRC4 pair
3.3V PCI clock output / Trusted Mode Enable (TME) Latched Input. This pin is sampled on power-up as
follows
0 = Overclocking of CPU and SRC Allowed
1 = Overclocking of CPU and SRC NOT allowed
After being sampled on power-up, this pin becomes a 3.3V PCI Output
3.3V PCI clock output.
3.3V PCI clock output / 27MH mode select for pin17, 18 strap. On powerup, the logic value on this pin
determines the power-up default of DOT_96/SRC0 and 27MHz/SRC1 output and the function table for the
pin17 and pin18.
Free running PCI clock output and ITP/SRC8 enable strap. This output is not affected by the state of the
PCI_STOP# pin. On powerup, the state of this pin determines whether pins 46 and 47 are an ITP or SRC
pair.
0 =SRC8/SRC8#
1 = ITP/ITP#
Ground for PCI clocks.
Power supply for USB clock, nominal 3.3V.
Fixed 48MHz USB clock output. 3.3V./ 3.3V tolerant input for CPU frequency selection. Refer to input
electrical characteristics for Vil_FS and Vih_FS values.
Ground pin for the 48MHz outputs.
True clock of SRC or DOT96. The power-up default function depends on 27_Select, 1= SRC0,
0=DOT96
Complement clock of SRC or DOT96. The power-up default function depends on 27_Select, 1= SRC0,
0=DOT96
Ground pin for the DOT96 clocks.
Power supply for SRC / SE1 and SE2 clocks, 3.3V nominal.
Byte 5, bit 6
1.05V to 3.3V from external power supply
2
DESCRIPTION
ICS9LPRS365
Datasheet