IDT72V3670L10PF IDT, Integrated Device Technology Inc, IDT72V3670L10PF Datasheet - Page 4

• Manufacturer Part Number: IDT72V3670L10PF
• Description: IC FIFO SYNC II 36BIT 128-TQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: 72Vr

Specifications of IDT72V3670L10PF

• Function: Asynchronous, Synchronous
• Memory Size: 288K (8K x 36)
• Data Rate: 166MHz
• Access Time: 10ns
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: -40°C ~ 80°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Configuration: Dual
• Density: 288Kb
• Access Time (max): 6.5ns
• Word Size: 36b
• Organization: 8Kx36
• Sync/async: Synchronous
• Expandable: Yes
• Bus Direction: Uni-Directional
• Package Type: TQFP
• Clock Freq (max): 100MHz
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3.15V
• Operating Supply Voltage (max): 3.45V
• Supply Current: 40mA
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 128
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 72V3670L10PF; 800-1536

words written to the FIFO do require a LOW on REN for access. The state of
the FWFT/SI input during Master Reset determines the timing mode in use.
can provide, the FWFT timing mode permits depth expansion by chaining FIFOs
in series (i.e. the data outputs of one FIFO are connected to the corresponding
data inputs of the next). No external logic is required.
FF/IR (Full Flag or Input Ready), HF (Half-full Flag), PAE (Programmable
Almost-Empty flag) and PAF (Programmable Almost-Full flag). The EF and FF
functions are selected in IDT Standard mode. The IR and OR functions are
selected in FWFT mode. HF, PAE and PAF are always available for use,
irrespective of timing mode.
memory. Programmable offsets determine the flag switching threshold and can
be loaded by two methods: parallel or serial. Eight default offset settings are also
provided, so that PAE can be set to switch at a predefined number of locations
from the empty boundary and the PAF threshold can also be set at similar
predefined values from the full boundary. The default offset values are set during
Master Reset by the state of the FSEL0, FSEL1, and LD pins.
IDT72V3640/50/60/70/80/90 3.3V HIGH DENSITY SUPERSYNC II
1,024 x 36, 2,048 x 36, 4,096 x 36, 8,192 x 36, 16,384 x 36 and 32,768 x 36
For applications requiring more data storage capacity than a single FIFO
PAE and PAF can be programmed independently to switch at any point in
These FIFOs have five flag pins, EF/OR (Empty Flag or Output Ready),
PROGRAMMABLE ALMOST-FULL (PAF)
FULL FLAG/INPUT READY (FF/IR)
FIRST WORD FALL THROUGH/
(x36, x18, x9) DATA IN (D
WRITE CLOCK (WCLK/WR*)
SERIAL INPUT (FWFT/SI)
WRITE ENABLE (WEN)
SERIAL ENABLE(SEN)
PARTIAL RESET (PRS)
INPUT WIDTH (IW)
Figure 1. Single Device Configuration Signal Flow Diagram
LOAD (LD)
0
- D
n
)
MATCHING
72V3640
72V3650
72V3660
72V3670
72V3680
72V3690
(BM)
BUS-
IDT
TM
36-BIT FIFO
4
MASTER RESET (MRS)
WCLK, are used to load the offset registers via the Serial Input (SI). For parallel
programming, WEN together with LD on each rising edge of WCLK, are used
to load the offset registers via D
of RCLK can be used to read the offsets in parallel from Q
serial or parallel offset loading has been selected.
pointers are set to the first location of the FIFO. The FWFT pin selects IDT
Standard mode or FWFT mode.
location of the memory. However, the timing mode, programmable flag
programming method, and default or programmed offset settings existing before
Partial Reset remain unchanged. The flags are updated according to the timing
mode and offsets in effect. PRS is useful for resetting a device in mid-operation,
when reprogramming programmable flags would be undesirable.
Empty flag) and PAF (Programmable Almost-Full flag) outputs. The timing
modes can be set to be either asynchronous or synchronous for the PAE and
PAF flags.
For serial programming, SEN together with LD on each rising edge of
During Master Reset (MRS) the following events occur: the read and write
The Partial Reset (PRS) also sets the read and write pointers to the first
It is also possible to select the timing mode of the PAE (Programmable Almost-
OUTPUT WIDTH (OW)
RETRANSMIT (RT)
PROGRAMMABLE ALMOST-EMPTY (PAE)
READ CLOCK (RCLK/RD*)
READ ENABLE (REN)
EMPTY FLAG/OUTPUT READY (EF/OR)
HALF-FULL FLAG (HF)
BIG-ENDIAN/LITTLE-ENDIAN (BE)
INTERSPERSED/
NON-INTERSPERSED PARITY (IP)
OUTPUT ENABLE (OE)
(x36, x18, x9) DATA OUT (Q
n
. REN together with LD on each rising edge
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
0
- Q
OCTOBER 22, 2008
n
n
regardless of whether
)
4667 drw03