STE100A ST Microelectronics, Inc., STE100A Datasheet - Page 8
STE100A
Manufacturer Part Number
STE100A
Description
PCI 10/100 Ethernet Controller with Integrated PHY (3.3v)
Manufacturer
ST Microelectronics, Inc.
Datasheet
1.STE100A.pdf
(82 pages)
- Current page: 8 of 82
- Download datasheet (590Kb)
Pin description
8/82
Table 1.
PCI bus interface
120,121
123,124
126,127
Pin no.
32~35
12,13
15,16
29,30
43,44
46,47
49,50
52,53
9,10
113
114
116
117
118
119
1,2
6,7
37
41
Pin description
AD-13~10
AD-31,30
AD-29,28
AD-27,26
AD-25,24
AD-23,22
AD-21,20
AD-19,18
AD-17,16
AD-15,14
PCI-CLK
AD-7, 6
AD-5,4
AD-3,2
AD-1,0
Name
INTA#
GNT#
REQ#
PME#
RST#
AD-9
AD-8
Type
O/D
OD
I/O
O
O
I
I
I
PCI interrupt request. STE10/100A asserts this signal when
one of the interrupt event is set.
PCI reset signal to initialize the STE10/100A. The RST signal
should be asserted for at least 100µs to ensure that the
STE10/100A completes initialization. During the reset period,
all the output pins of STE10/100A will be placed in a high-
impedance state and all the O/D pins are floated.
PCI clock input to STE10/100A for PCI bus functions. The
Bus signals are synchronized relative to the rising edge of
PCI-CLK PCI-CLK must operate at a frequency in the range
between 20MHz and 33MHz to ensure proper network
operation.
PCI bus granted. This signal indicates that the STE10/100A
has been granted ownership of the PCI bus as a result of a
bus request.
PCI bus request. STE10/100A asserts this line when it needs
access to the PCI Bus.
The power management event signal is an open drain, active
low signal. The STE10/100A will assert PME# to indicate that
a power management event has occurred.
When WOL (bit 18 of CSR18) is set, the STE10/100A is
placed in wake on LAN mode. While in this mode, the
STE10/100A will activate the PME# signal upon receipt of a
magic packet frame from the network.
In the wake on LAN mode, when LWS (bit 17 of CSR18) is
set, the LAN-wake signal follows HP’s protocol; otherwise, it
is IBM protocol.
Multiplexed PCI bus address/data pins
Description
STE10/100A
Related parts for STE100A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-channel 200V - 0.022
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 100V - 0.0045
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
81 x 128 Single-chip LCD Controller/driver
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
N-channel 900V - 0.14
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 800V - 0.11
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 55V - 0.07 Ohm - 22A StripFET Power MOSFET
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Old PRODUCT: Not Suitable For Design-in
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
High-voltage, High Current Switch
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Single Chip Read & Write Channel
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
10A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
20A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
-
Manufacturer:
ST Microelectronics, Inc.
Datasheet: