STE100A ST Microelectronics, Inc., STE100A Datasheet - Page 10
STE100A
Manufacturer Part Number
STE100A
Description
PCI 10/100 Ethernet Controller with Integrated PHY (3.3v)
Manufacturer
ST Microelectronics, Inc.
Datasheet
1.STE100A.pdf
(82 pages)
- Current page: 10 of 82
- Download datasheet (590Kb)
Pin description
10/82
Table 1.
Physical interface
LED display & miscellaneous
107,109
105,104
Pin no.
101
98
97
90
92
Pin description (continued)
RX+, RX-
TX+, TX-
LED M1-
LED M2-
LED M1-
LED M2-
100 link
LK/Act
Speed
Name
Iref
Act
X1
X2
or
or
Type
O
O
O
O
O
I
I
25MHz reference clock input for physical portion. When an
external 25MHz crystal is used, this pin will be connected to
one of its terminals, and X2 will be connected to the other
terminal. If an external 25 MHz oscillator is used, then this
pin will be connected to the oscillator’s output pin.
25MHz reference clock output for physical portion. When an
external 25MHz crystal is used, this pin will be connected to
one of the crystal terminals (see X1, above). If an external
clock source is used, then this pin should be left open.
The differential transmit outputs of 100BASE-TX or 10BASE-
T, these pins connect directly to magnetic.
The differential receive inputs of 100BASE-TX or 10BASE-T,
these pins connect directly from magnetic.
Reference resistor connecting pin for reference current,
directly connects a 5KOhm ± 1% resistor to Vss.
This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for link and activity status. This pin will be driven
on continually when a good Link test is detected. This pin will
be driven at a 10Hz blinking frequency when either effective
receiving or transmitting is detected.
For mode 2:
LED display for activity status. This pin will be driven at a
10Hz blinking frequency when either effective receiving or
transmitting is detected.
This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for 100M b/s or 10M b/s speed. This pin will be
driven on continually when the 100M b/s network operating
speed is detected.
For mode 2:
LED display for 100Ms/s link status. This pin will be driven on
continually when 100Mb/s network operating speed is
detected.
Description
STE10/100A
Related parts for STE100A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-CHANNEL ENHANCEMENT MODE Power MOS Transistor
Manufacturer:
ST Microelectronics
Datasheet:
Part Number:
Description:
N-channel 200V - 0.022
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 100V - 0.0045
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
81 x 128 Single-chip LCD Controller/driver
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
N-channel 900V - 0.14
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 800V - 0.11
Manufacturer:
ST Microelectronics, Inc.
Part Number:
Description:
N-channel 55V - 0.07 Ohm - 22A StripFET Power MOSFET
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Old PRODUCT: Not Suitable For Design-in
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
High-voltage, High Current Switch
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
Single Chip Read & Write Channel
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
10A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
20A Triacs
Manufacturer:
ST Microelectronics, Inc.
Datasheet:
Part Number:
Description:
-
Manufacturer:
ST Microelectronics, Inc.
Datasheet: