MBM29DL16XTE70PFTN Meet Spansion Inc., MBM29DL16XTE70PFTN Datasheet - Page 30

• Manufacturer Part Number: MBM29DL16XTE70PFTN
• Description: Flash Memory Cmos 16m 2m ? 8/1m ? 16 Bit Dual Operation
• Manufacturer: Meet Spansion Inc.

30
MBM29DL16XTD/BD
• Automatic Sleep Mode
• Output Disable
• Autoselect
When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at V
taken high, the device requires t
In the standby mode the outputs are in the high impedance state, independent of the OE input.
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29DL16XTD/BD data. This mode can be used effectively with an application requested low power
consumption such as handy terminals.
To activate this mode, MBM29DL16XTD/BD automatically switch themselves to low power mode when
MBM29DL16XTD/BD addresses remain stably during access fine of 150 ns. It is not necessary to control CE,
WE, and OE on the mode. Under the mode, the current consumed is typically 1 μA (CMOS Level).
During simultaneous operation, V
Since the data are latched during this mode, the data are read-out continuously. If the addresses are changed,
the mode is canceled automatically and MBM29DL16XTD/BD read-out the data for changed addresses.
With the OE input at a logic high level (V
to be in a high impedance state.
The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the devices to be programmed with its corresponding programming algorithm. This mode is functional over the
entire temperature range of the devices.
To activate this mode, the programming equipment must force V
identifier bytes may then be sequenced from the devices outputs by toggling address A
addresses are DON’T CARES except A
Tables (BYTE = V
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29DL16XTD/BD are erased or programmed in a system without access to high voltage on the A
command sequence is illustrated in “MBM29DL16XTD/BD Command Definitions Table” (in ■DEVICE BUS
OPERATION). (Refer to Autoselect Command section.)
Byte 0 (A
identifier code (MBM29DL161TD = 36h and MBM29DL161BD = 39h for ×8 mode; MBM29DL161TD = 2236h
and MBM29DL161BD = 2239h for ×16 mode), (MBM29DL162TD = 2Dh and MBM29DL162BD = 2Eh for ×8
mode; MBM29DL162TD = 222Dh and MBM29DL162BD = 222Eh for ×16 mode), (MBM29DL163TD = 28h and
MBM29DL163BD = 2Bh for ×8 mode; MBM29DL163TD = 2228h and MBM29DL163BD = 222Bh for ×16 mode),
(MBM29DL164TD = 33h and MBM29DL164BD = 35h for ×8 mode; MBM29DL164TD = 2233h and
MBM29DL164BD = 2235h for ×16 mode). These two bytes/words are given in “MBM29DL161TD/BD,
MBM29DL162TD/BD, MBM29DL163TD/BD and MBM29DL164TD/BD Sector Group Protection Verify
Autoselect Codes Tables” and these “Extended Autoselect Code Tables” in ■DEVICE BUS OPERATION. All
identifiers for manufactures and device will exhibit odd parity with DQ
the proper device codes when executing the autoselect, A
MBM29DL162TD/BD, MBM29DL163TD/BD and MBM29DL164TD/BD Sector Group Protection Verify
Autoselect Codes Tables” and these “Extended Autoselect Code Tables” in ■DEVICE BUS OPERATION.)
In case of applying V
can not be executed.
(CE = “H” or “L”). Under this condition the current is consumed is less than 5 μA Max. Once the RESET pin is
0
= V
IL
) represents the manufacturer’s code (Fujitsu = 04h) and word 1 (A
IH
and BYTE = V
ID
on A
9
, since both Bank 1 and Bank 2 enters Autoselect mode, the simultenous operation
RH
CC
IL
of wake up time before outputs are valid for read access.
)” in ■DEVICE BUS OPERATION.)
active current (I
Retired Product DS05-20874-8E_July 12, 2007
IH
0
, A
), output from the devices are disabled. This will cause the output pins
-70/90
1
, and A
6
CC2
(A
) is required.
-1
). (See “MBM29DL16XTD/BD User Bus Operations
1
must be V
ID
(11.5 V to 12.5 V) on address pin A
7
IL
defined as the parity bit. In order to read
. (See “MBM29DL161TD/BD,
0
= V
IH
) represents the device
0
from V
IL
SS
to V
± 0.3 V
9
IH
pin. The
9
. Two
. All