TMPM361F10FG Toshiba, TMPM361F10FG Datasheet - Page 160

• Manufacturer Part Number: TMPM361F10FG
• Manufacturer: Toshiba

Specifications of TMPM361F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Contact Us
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 100
• Package: LQFP(14Ã?14)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 3
• Uart/sio (ch): 5
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: 8
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

8.2
Port functions
8.2.3
Type
8.2.3.1
8.2.3.2
in units of bits. Besides the general-purpose input / output function, the port E performs the address bus
(A17 to A23) function, the serial interface function (UART / SIO), the external signal interrupt function, the
16-bit timer input function and clock output function.
to the corresponding bit of the three registers. If you use the port E as other than a general-purpose port, set
"1" to the corresponding bit of the function register. Do not set "1" to the some function registers at the same
time.
put in the PEIE register. These settings enable the interrupt input even if the CGSTBYCR<DRVE> bit in the
clock / mode control block is set to stop driving of pins during STOP mode.
Port E data register
Port E output control register
Port E function register 1
Port E function register 2
Port E function register 3
Port E open drain control register
Port E pull-up control register
Port E input control register
Port E (PE0 to PE7)
The port E is a general-purpose, 8-bit input / output port. For this port, inputs and outputs can be specified
Reset initializes all bits of the port E as general-purpose ports with input, output and pull-up disabled.
The Port E has three types of of function register. If you use the port E as a general-purpose port, set "0"
If this port is used for the external bus function, PECR and PEFR1 must be set to "1".
To use the external interrupt input for releasing STOP mode, select this function in the PEFR2 and enable in-
Note:In modes other than STOP mode, interrupt input is enabled regardless of the PEFR2 register setting
Port E Circuit Type
Port E register
if input is enabled in PxIE. Make sure to disable unused interrupts when programming the device.
T6
7
T4
6
Register name
T3
5
Page 136
T2
4
PEDATA
PEPUP
PEFR1
PEFR2
PEFR3
PEOD
PECR
PEIE
T3
3
Base Address = 0x400C_0400
T3
2
Address (Base+)
0x000C
0x002C
0x0000
0x0004
0x0008
0x0010
0x0028
0x0038
T3
1
TMPM361F10FG
T3
0