73S1217F Maxim, 73S1217F Datasheet - Page 83
73S1217F
Manufacturer Part Number
73S1217F
Description
The Teridian 73S1217F is a self-contained SoC smart card reader IC that is an ideal solution for any USB-connected ISO 7816 design
Manufacturer
Maxim
Datasheet
1.73S1217F.pdf
(140 pages)
- Current page: 83 of 140
- Download datasheet (2Mb)
There are two, two-byte FIFOs that are used to buffer transmit and receive data. During a T=0 processing, if
a parity error is detected by the 73S1217F during message reception, an error signal (BREAK) will be
generated to the smart card. The byte received will be discarded and the firmware notified of the error.
Break generation and receive byte dropping can be disabled under firmware control. During the
transmission of a byte, if an error signal (BREAK) is detected, the last byte is retransmitted again and the
firmware notified. Retransmission can be disabled by firmware. When a correct byte is received, an
interrupt is generated to the firmware, which then reads the byte from the receive FIFO. Receive overruns
are detected by the hardware and reported via an interrupt. During transmission of a message, the firmware
will write bytes into the transmit FIFO. The hardware will send them to the smart card. When the last byte of
a message has been written, the firmware will need to set the LASTTX bit in the
cause the hardware to insert the CRC/LRC if in a T=1 protocol mode. CRC/LRC generation/checking is only
provided during T=1 processing. Firmware will need to instruct the smart function to go into receive mode
after this last transmit data byte if it expects a response from the smart card. At the end of the smart card
response, the firmware will put the interface back into transmit mode if appropriate.
The hardware can check for the following card-related timeouts:
•
•
•
The firmware will load the Wait Time registers with the appropriate value for the operating mode at the
appropriate time.
an interrupt will be generated and the firmware can take appropriate recovery steps. Support is provided
for adding additional guard times between characters using the
between the last byte received by the 73S1217F and the first byte transmitted by the 73S1217F using the
Block Guard Time register
responsible for all protocol checking and error recovery.
Rev. 1.2
Character Waiting Time (CWT).
Block Waiting Time (BWT).
Initial Waiting Time (IWT).
SCSCLK(5:0)
MCLK =
96MHz
PLL
SCSel(3:2)
SCCLK(5:0)
Figure 21
F/D Register
(BGT). Other than the protocol checks described above, the firmware is
Figure 20: Smart Card CLK and ETU Generation
shows the guard, block, wait and ATR time definitions. If a timeout occurs,
Pre-Scaler
Pre-Scaler
6 bits
6 bits
1/13
1/13
FDReg(7:4)
7.38M
7.38M
FDReg(3:0)
7.38M
MSCLKE
MSCLK
Extra Guard Time register (EGT)
ETU Divider
FI Decoder
12 bits
1/744
Defaults
in Italics
DIV
DIV
by
by
2
2
STXCtl
9926
3.69M
3.69M
ETUCLK
SYNC
SCLK
CLK
SFR. This will
CENTER
EDGE
and
83
Related parts for 73S1217F
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
The DS5250 is a highly secure, four clocks-per-machine cycle, 100% 8051-instruction-set-compatible microprocessor in Maxim's secure microcontroller family
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
The MAX9263/MAX9264 chipset extends Maxim's gigabit multimedia serial link (GMSL) technology to include high-bandwidth digital content protection (HDCP) encryption for content protection of DVD and Blu-ray™ video and audio data
Manufacturer:
Maxim
Part Number:
Description:
The Maxim MXL1016 (10ns, typ) high-speed, complementary-output comparator is designed specifically to
interface directly to TTL logic while operating from
either a dual ±5V supply or a single +5V supply
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's DG300–DG303 and DG300A–DG303A CMOS dual and quad analog switches combine low power operation with fast switching times and superior DC and AC switch characteristics
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's DG300–DG303 and DG300A–DG303A CMOS dual and quad analog switches combine low power operation with fast switching times and superior DC and AC switch characteristics
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's DG300–DG303 and DG300A–DG303A CMOS dual and quad analog switches combine low power operation with fast switching times and superior DC and AC switch characteristics
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's DG300–DG303 and DG300A–DG303A CMOS dual and quad analog switches combine low power operation with fast switching times and superior DC and AC switch characteristics
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG401/DG403/DG405 analog switches now feature guaranteed low on-resistance matching between switches (2Ω max) and guaranteed on-resistance flatness over the signal range (3Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG401/DG403/DG405 analog switches now feature guaranteed low on-resistance matching between switches (2Ω max) and guaranteed on-resistance flatness over the signal range (3Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG401/DG403/DG405 analog switches now feature guaranteed low on-resistance matching between switches (2Ω max) and guaranteed on-resistance flatness over the signal range (3Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG406 and DG407 CMOS analog multiplexers now feature guaranteed matching between channels (8Ω max) and flatness over the specified signal range (9Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG406 and DG407 CMOS analog multiplexers now feature guaranteed matching between channels (8Ω max) and flatness over the specified signal range (9Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG408 and DG409 CMOS analog multiplexers now feature guaranteed matching between channels (8Ω max) and flatness over the specified signal range (9Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG408 and DG409 CMOS analog multiplexers now feature guaranteed matching between channels (8Ω max) and flatness over the specified signal range (9Ω max)
Manufacturer:
Maxim
Datasheet:
Part Number:
Description:
Maxim's redesigned DG411/DG412/DG413 analog switches now feature low on-resistance matching between switches (3Ω max) and guaranteed on-resistance flatness over the signal range (Δ4Ω max)
Manufacturer:
Maxim
Datasheet: