ST72264G2 STMicroelectronics, ST72264G2 Datasheet - Page 153

• Manufacturer Part Number: ST72264G2
• Description: 8-bit MCU
• Manufacturer: STMicroelectronics

Specifications of ST72264G2

• 4 K Or 8 Kbytes Program Memory: ROM or single voltage extended Flash (XFlash) with read-out protection, write protection, In-Circuit Programming and In-Application Programming (ICP and IAP). 10K write/erase cycles guaranteed, data retention
• Clock Sources: crystal/ceramic resonator oscillators, internal RC oscillator and bypass for external clock
• 4 Power Saving Modes: Halt, Active Halt,Wait and Slow
• Two 16-bit Timers With: 2 input captures, 2 output compares, external clock input on one timer, PWM and Pulse generator modes

13.11 COMMUNICATION INTERFACE CHARACTERISTICS
13.11.1 SPI - Serial Peripheral Interface
Subject to general operating conditions for V
f
Figure 93. SPI Slave Timing Diagram with CPHA=0
Notes:
1. Data based on design simulation and/or characterisation results, not tested in production.
2. When no communication is on-going the data output line of the SPI (MOSI in master mode, MISO in slave mode) has
its alternate function capability released. In this case, the pin status depends on the I/O port configuration.
3. Measurement points are done at CMOS levels: 0.3xV
OSC
Symbol
1/t
t
t
w(SCKH)
w(SCKL)
t
t
t
t
t
t
t
t
dis(SO)
t
t
t
t
r(SCK)
su(SS)
f(SCK)
t
su(MI)
t
v(MO)
h(MO)
f
su(SI)
a(SO)
v(SO)
h(SO)
MISO
MOSI
h(SS)
h(MI)
c(SCK)
h(SI)
, and T
SCK
SS
CPHA=0
CPOL=0
CPHA=0
CPOL=1
OUTPUT
INPUT
INPUT
A
SPI clock frequency
SPI clock rise and fall time
SS setup time
SS hold time
SCK high and low time
Data input setup time
Data input hold time
Data output access time
Data output disable time
Data output valid time
Data output hold time
Data output valid time
Data output hold time
unless otherwise specified.
see note 2
t
a(SO)
t
su(SS)
t
su(SI)
Parameter
t
t
MSB IN
w(SCKH)
w(SCKL)
MSB OUT
t
t
h(SI)
c(SCK)
t
DD
v(SO)
DD
Slave
,
Master
Slave
Slave
Slave
Master
Slave
Master
Slave
Master
Slave
Slave
Slave (after enable edge)
Master (before capture edge)
BIT6 OUT
and 0.7xV
Refer to I/O port characteristics for more details on
the input/output alternate function characteristics
(SS, SCK, MOSI, MISO).
3)
Conditions
ST72260Gx, ST72262Gx, ST72264Gx
DD
BIT1 IN
.
t
f
f
h(SO)
CPU
CPU
=8MHz
=8MHz
t
t
r(SCK)
f(SCK)
f
CPU
LSB IN
0.0625
see I/O port pin description
0.25
0.25
Min
120
120
100
100
100
100
100
90
LSB OUT
0
0
0
/128
t
h(SS)
f
f
CPU
CPU
Max
120
240
120
2
4
/4
/2
t
dis(SO)
153/172
Unit
t
MHz
CPU
ns
note 2
see