STM32F417IE STMicroelectronics, STM32F417IE Datasheet - Page 121
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM32F417IE
Manufacturer Part Number
STM32F417IE
Description
High-performance and DSP with FPU, ARM Cortex-M4 MCU with 512 Kbytes Flash, 168 MHz CPU, Art Accelerator, Ethernet, HW crypto
Manufacturer
STMicroelectronics
Datasheet
1.STM32F415ZG.pdf
(168 pages)
Specifications of STM32F417IE
Core
ARM 32-bit Cortex™-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions
3×12-bit, 2.4 Msps A/d Converters
up to 24 channels and 7.2 MSPS in triple interleaved mode
General-purpose Dma
16-stream DMA controller with FIFOs and burst support
Up To 17 Timers
up to twelve 16-bit and two 32-bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
10/100 Ethernet Mac With Dedicated Dma
supports IEEE 1588v2 hardware, MII/RMII
Cryptographic Acceleration
hardware acceleration for AES 128, 192, 256, Triple DES, HASH (MD5, SHA-1), and HMAC
Rtc
subsecond accuracy, hardware calendar
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM32F417IEH6
Manufacturer:
ST
Quantity:
20 000
STM32F415xx, STM32F417xx
Note:
Equation 1: R
The formula above
allowed for an error below 1/4 of LSB. N = 12 (from 12-bit resolution) and k is the number of
sampling periods defined in the ADC_SMPR1 register.
Table 66.
1. Better performance could be achieved in restricted V
2. Based on characterization, not tested in production.
3. If an inverted reset signal is applied to PDR_ON, this value can be lowered to 1.7 V when the device
ADC accuracy vs. negative injection current: Injecting a negative current on any of the
standard (non-robust) analog input pins should be avoided as this significantly reduces the
accuracy of the conversion being performed on another analog input. It is recommended to
add a Schottky diode (pin to ground) to standard analog pins which may potentially inject
negative currents.
Any positive injection current within the limits specified for I
Section 5.3.16
Symbol
a
operates in a reduced temperature range (0 to 70 °C).
EO
EG
ED
ET
EL
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
ADC accuracy at f
AIN
does not affect the ADC accuracy.
Parameter
max formula
(Equation
R
AIN
1) is used to determine the maximum external impedance
Doc ID 022063 Rev 2
=
ADC
------------------------------------------------------------- - R
f
ADC
= 30 MHz
f
f
V
PCLK2
ADC
DDA
×
C
(
= 30 MHz, R
k 0.5
= 1.8
ADC
= 60 MHz,
Test conditions
–
DD
(1)
×
(3)
, frequency and temperature ranges.
ln
to 3.6 V
)
(
2
N
AIN
+
2
< 10 kΩ,
)
–
INJ(PIN)
ADC
Electrical characteristics
and ΣI
±1.5
±1.5
±1.5
Typ
±2
±1
INJ(PIN)
Max
±2.5
±3
±2
±5
±3
(2)
in
121/168
Unit
LSB