SAM3N0A Atmel Corporation, SAM3N0A Datasheet - Page 649
SAM3N0A
Manufacturer Part Number
SAM3N0A
Description
Manufacturer
Atmel Corporation
- Current page: 649 of 752
- Download datasheet (17Mb)
33. Analog-to-digital Converter (ADC)
33.1
33.2
11011A–ATARM–04-Oct-10
11011A–ATARM–04-Oct-10
Description
Embedded Characteristics
The ADC is based on a 10-bit Analog-to-Digital Converter (ADC) managed by an ADC Control-
ler. Refer to the Block Diagram:
making possible the analog-to-digital conversions of 16 analog lines. The conversions extend
from 0V to ADVREF. The ADC supports an 8-bit or 10-bit resolution mode, and conversion
results are reported in a common register for all channels, as well as in a channel-dedicated reg-
ister. Software trigger, external trigger on rising edge of the ADTRG pin or internal triggers from
Timer Counter output(s) are configurable.
The comparison circuitry allows automatic detection of values below a threshold, higher than a
threshold, in a given range or outside the range, thresholds and ranges being fully configurable.
The ADC also integrates a Sleep Mode and a conversion sequencer and connects with a PDC
channel. These features reduce both power consumption and processor intervention.
age node that may be equal to the analog supply voltage. An external decoupling capacitance is
required for noise filtering.
Finally, the user can configure ADC timings, such as Startup Time and Tracking Time.
A whole set of reference voltages is generated internally from a single external reference volt-
• 10-bit Resolution
• 500 kHz Conversion Rate
• Wide Range Power Supply Operation
• Integrated Multiplexer Offering Up to 16 Independent Analog Inputs
• Individual Enable and Disable of Each Channel
• Hardware or Software Trigger
• PDC Support
• Possibility of ADC Timings Configuration
• Two Sleep Modes and Conversion Sequencer
• Standby Mode for Fast Wakeup Time Response
• Automatic Window Comparison of Converted Values
• Write Protect Registers
– External Trigger Pin
– Timer Counter Outputs (Corresponding TIOA Trigger)
– Automatic Wakeup on Trigger and Back to Sleep Mode after Conversions of all
– Possibility of Customized Channel Sequence
– Power Down Capability
Enabled Channels
Figure
33-1. It also integrates a 16-to-1 analog multiplexer,
SAM3N
SAM3N
649
649
Related parts for SAM3N0A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Cortex M3 Flash Microcontroller Converges Performance and Simplicity
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: