RM9200 Atmel Corporation, RM9200 Datasheet - Page 88
RM9200
Manufacturer Part Number
RM9200
Description
Manufacturer
Atmel Corporation
Datasheets
1.M40800.pdf
(284 pages)
2.M40800.pdf
(153 pages)
3.RM9200.pdf
(350 pages)
4.RM9200.pdf
(149 pages)
5.RM9200.pdf
(41 pages)
6.RM9200.pdf
(701 pages)
Specifications of RM9200
Flash (kbytes)
0 Kbytes
Pin Count
256
Max. Operating Frequency
180 MHz
Cpu
ARM920
Hardware Qtouch Acquisition
No
Max I/o Pins
122
Ext Interrupts
122
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
1
Twi (i2c)
1
Uart
5
Ssc
3
Ethernet
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.3
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- M40800 PDF datasheet
- M40800 PDF datasheet #2
- RM9200 PDF datasheet #3
- RM9200 PDF datasheet #4
- RM9200 PDF datasheet #5
- RM9200 PDF datasheet #6
- Current page: 88 of 284
- Download datasheet (2Mb)
Memory Interface
3-18
Unidirectional data bus
When BUSEN is HIGH, all instructions and input data are presented on the input data
bus, DIN[31:0]. The timing of this data is similar to that of the bidirectional bus when
in input mode. Data must be set up and held to the falling edge of MCLK. For the exact
timing requirements refer to Chapter 7 AC and DC Parameters.
In this configuration, all output data is presented on DOUT[31:0]. The value on this bus
only changes when the processor performs a store cycle. Again, the timing of the data
is similar to that of the bidirectional data bus. The value on DOUT[31:0] changes after
the falling edge of MCLK.
The bus timing of a read-write-read cycle combination is shown in Figure 3-13.
When the unidirectional data buses are being used, and BUSEN is HIGH, the
bidirectional bus, D[31:0], must be left unconnected.
The unidirectional buses are typically used internally in ASIC embedded applications.
Externally, most systems still require a bidirectional data bus to interface to external
memory. Figure 3-14 on page 3-19 shows how you can join the unidirectional buses up
at the pads of an ASIC to connect to an external bidirectional bus.
Copyright © 1994-2001. All rights reserved.
DOUT[31:0]
DIN[31:0]
D[31:0]
MCLK
read cycle
D[31:0]
MCLK
D1
D1
Figure 3-13 Unidirectional bus timing
write cycle
Figure 3-12 Bidirectional bus timing
read cycle write cycle read cycle
Dout
read cycle
Dout
ARM DDI 0029G
D2
D2
Related parts for RM9200
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: