ATxmega256A3 Atmel Corporation, ATxmega256A3 Datasheet - Page 139

• Manufacturer Part Number: ATxmega256A3
• Manufacturer: Atmel Corporation

Specifications of ATxmega256A3

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 50
• Ext Interrupts: 50
• Usb Speed: No
• Usb Interface: No
• Spi: 10
• Twi (i2c): 2
• Uart: 7
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 7
• Output Compare Channels: 22
• Input Capture Channels: 22
• Pwm Channels: 22
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.14.3
13.14.4
13.14.5
13.14.6
8077H–AVR–12/09
DIRCLR - Data Direction Clear Register
DIRTGL - Data Direction Toggle Register
OUT - Data Output Value
OUTSET - Data Output Value Set Register
• Bit 7:0 - DIRCLR[7:0]: Port Data Direction Clear
This register can be used instead of a Read-Modify-Write to set individual pins as input. Writing
a one to a bit will clear the corresponding bit in the DIR register. Reading this register will return
the value of the DIR register.
• Bit 7:0 - DIRTGL[7:0]: Port Data Direction Toggle
This register can be used instead of a Read-Modify-Write to toggle the direction on individual
pins. Writing a one to a bit will toggle the corresponding bit in the DIR register. Reading this reg-
ister will return the value of the DIR register.
• Bit 7:0 - OUT[7:0]: Port Data Output value
This register sets the data output value for the individual pins in the port. If OUTn is written to
one, pin n is driven high. If OUTn is written to zero, pin n is driven low. For this setting to have
any effect the pin direction must be set as output.
Bit
+0x03
Read/Write
Initial Value
Bit
+0x04
Read/Write
Initial Value
Bit
+0x02
Read/Write
Initial Value
Bit
+0x05
Read/Write
Initial Value
R/W
R/W
R/W
R/W
7
0
7
0
7
0
7
0
R/W
R/W
R/W
R/W
6
0
6
0
6
0
6
0
R/W
R/W
R/W
R/W
5
0
5
0
5
0
5
0
R/W
R/W
R/W
R/W
4
0
4
0
4
0
4
0
OUTSET[7:0]
DIRCLR[7:0]
DIRTGL[7:0]
OUT[7:0]
R/W
R/W
R/W
R/W
3
0
3
0
3
0
3
0
R/W
R/W
R/W
R/W
2
0
2
0
2
0
2
0
R/W
R/W
R/W
R/W
1
0
1
0
1
0
1
0
XMEGA A
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
OUTSET
DIRCLR
DIRTGL
OUT
139