ATtiny261 Atmel Corporation, ATtiny261 Datasheet - Page 39

• Manufacturer Part Number: ATtiny261
• Manufacturer: Atmel Corporation

Specifications of ATtiny261

• Flash (kbytes): 2 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

7.4
7.4.1
7.4.2
2588E–AVR–08/10
Register Description
MCUCR – MCU Control Register
PRR – Power Reduction Register
Refer to
able Register 1” on page 162
The MCU Control Register contains control bits for power management.
• Bit 5 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
• Bits 4, 3 – SM1:0: Sleep Mode Select Bits 2:0
These bits select between the three available sleep modes as shown in
Table 7-2.
• Bit 2 – Res: Reserved Bit
This bit is reserved and will always read zero.
The Power Reduction Register provides a method to reduce power consumption by allowing
peripheral clock signals to be disabled.
• Bits 7, 6, 5, 4 – Res: Reserved Bits
These bits are reserved and will always read zero.
• Bit 3 – PRTIM1: Power Reduction Timer/Counter1
Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1
is enabled, operation will continue like before the shutdown.
Bit
0x35 (0x55)
Read/Write
Initial Value
Bit
0x36 (0x56)
Read/Write
Initial Value
SM1
0
0
1
1
“DIDR0 – Digital Input Disable Register 0” on page 162
7
–
R
0
Sleep Mode Select
7
–
R
0
6
PUD
R/W
0
6
-
R
0
SM0
0
1
0
1
for details.
5
SE
R/W
0
5
-
R
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Standby
4
SM1
R/W
0
4
-
R
0
3
SM0
R/W
0
3
PRTIM1
R/W
0
2
—
R
0
2
PRTIM0
R/W
0
or
“DIDR1 – Digital Input Dis-
1
ISC01
R/W
0
1
PRUSI
R/W
0
Table
0
ISC00
R/W
0
7-2.
0
PRADC
R/W
0
MCUCR
PRR
39