ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 172

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.5.5.2
15.5.6
15.5.6.1
15.5.6.2
172
ATtiny87/ATtiny167
Bit Timing
Busy Signal in UART Mode
Baud rate Generator
Re-synchronization in LIN Mode
When the busy signal is set, some registers are locked, user writing is not allowed:
If the busy signal is set, the only available commands are:
Note that, if another command is entered during busy signal, the new command is not vali-
dated and the LOVRERR bit flag of the LINERR register is set. The on-going transfer is not
interrupted.
During the byte transmission, the busy signal is set. This locks some registers from being
written:
The busy signal is not generated during a byte reception.
The baud rate is defined to be the transfer rate in bits per second (bps):
Equation for calculating baud rate:
Equation for setting LINDIV value:
Note that in reception a majority vote on three samplings is made.
When waiting for Rx Header, LBT[5:0] = 32 in LINBTR register. The re-synchronization begins
when the BREAK is detected. If the BREAK size is not in the range (10.5 bits min., 28 bits
max. — 13 bits nominal), the BREAK is refused. The re-synchronization is done by adjusting
LBT[5:0] value to the SYNCH field of the received header (0x55). Then the PROTECTED
IDENTIFIER is sampled using the new value of LBT[5:0].
• “LIN Control Register” - LINCR - except LCMD[2:0], LENA & LSWRES,
• “LIN Baud Rate Registers” - LINBRRL & LINBRRH,
• “LIN Data Length Register” - LINDLR,
• “LIN Identifier Register” - LINIDR,
• “LIN Data Register” - LINDAT.
• LCMD[1:0] = 00
• LENA = 0 and/or LCMD[2] = 0, the kill command is taken into account immediately,
• LSWRES = 1, the reset command is taken into account immediately.
• “LIN Control Register” - LINCR - except LCMD[2:0], LENA & LSWRES,
• “LIN Data Register” - LINDAT.
• BAUD: Baud rate (in bps),
•
• LDIV[11:0]: Contents of LINBRRH & LINBRRL registers - (0-4095), the pre-scaler receives
• LBT[5:0]: Least significant bits of - LINBTR register- (0-63) is the number of samplings in a
f
clk
LIN or UART bit (default value 32).
clk
i/o
i/o
as input clock.
: System I/O clock frequency,
b
, the abort command is taken into account at the end of the byte,
BAUD = fclk
LDIV[11:0] = ( fclk
i/o
/ LBT[5:0] x (LDIV[11:0] + 1)
i/o
/ LBT[5:0] x BAUD ) - 1
8265B–AVR–09/10