ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 151
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega8515
Manufacturer Part Number
ATmega8515
Description
Manufacturer
Atmel Corporation
Specifications of ATmega8515
Flash (kbytes)
8 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
35
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Input Capture Channels
1
Pwm Channels
3
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA8515
Manufacturer:
ATMEL
Quantity:
5 510
Company:
Part Number:
ATMEGA8515
Manufacturer:
NS
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
AT
Quantity:
20 000
Company:
Part Number:
ATmega8515-16AC
Manufacturer:
MOT
Quantity:
3 450
Part Number:
ATmega8515-16AC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL
Quantity:
4 500
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16PU
Manufacturer:
AT
Quantity:
20 000
Multi-processor
Communication Mode
2512K–AVR–01/10
Table 61. Recommended Maximum Receiver Baud Rate Error for Normal Speed Mode
(U2X = 0)
Table 62. Recommended Maximum Receiver Baud Rate Error for Double Speed Mode
(U2X = 1)
The recommendations of the maximum Receiver Baud Rate error was made under the
assumption that the Receiver and Transmitter equally divides the maximum total error.
There are two possible sources for the Receiver’s baud rate error. The Receiver’s sys-
tem clock (XTAL) will always have some minor instability over the supply voltage range
and the temperature range. When using a crystal to generate the system clock, this is
rarely a problem, but for a resonator the system clock may differ more than 2% depend-
ing of the resonators tolerance. The second source for the error is more controllable.
The baud rate generator can not always do an exact division of the system frequency to
get the baud rate wanted. In this case an UBRR value that gives an acceptable low error
can be used if possible.
Setting the Multi-processor Communication mode (MPCM) bit in UCSRA enables a fil-
tering function of incoming frames received by the USART Receiver. Frames that do not
contain address information will be ignored and not put into the receive buffer. This
effectively reduces the number of incoming frames that has to be handled by the CPU,
in a system with multiple MCUs that communicate via the same serial bus. The Trans-
mitter is unaffected by the MPCM setting, but has to be used differently when it is a part
of a system utilizing the Multi-processor Communication mode.
If the Receiver is set up to receive frames that contain 5 to 8 data bits, then the first stop
bit indicates if the frame contains data or address information. If the Receiver is set up
for frames with nine data bits, then the ninth bit (RXB8) is used for identifying address
and data frames. When the frame type bit (the first stop or the ninth bit) is one, the frame
contains an address. When the frame type bit is zero the frame is a data frame.
# (Data+Parity Bit)
# (Data+Parity Bit)
10
10
D
5
6
7
8
9
D
5
6
7
8
9
R
R
slow
93.20
94.12
94.81
95.36
95.81
96.17
slow
94.12
94.92
95.52
96.00
96.39
96.70
(%)
(%)
R
R
106.67
105.79
105.11
104.58
104.14
103.78
105.66
104.92
104.35
103.90
103.53
103.23
fast
fast
(%)
(%)
+5.79/-5.88
+5.11/-5.19
+4.58/-4.54
+4.14/-4.19
+3.78/-3.83
+5.66/-5.88
+4.92/-5.08
+4.32/-4.48
+3.90/-4.00
+3.53/-3.61
+3.23/-3.30
Max Total
+6.67/-6.8
Max Total
Error (%)
Error (%)
ATmega8515(L)
Recommended Max
Recommended Max
Receiver Error (%)
Receiver Error (%)
± 3.0
± 2.5
± 2.0
± 2.0
± 1.5
± 1.5
± 2.5
± 2.0
± 1.5
± 1.5
± 1.5
± 1.0
151