ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega8515
Manufacturer Part Number
ATmega8515
Description
Manufacturer
Atmel Corporation
Specifications of ATmega8515
Flash (kbytes)
8 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
35
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Input Capture Channels
1
Pwm Channels
3
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA8515
Manufacturer:
ATMEL
Quantity:
5 510
Company:
Part Number:
ATMEGA8515
Manufacturer:
NS
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
AT
Quantity:
20 000
Company:
Part Number:
ATmega8515-16AC
Manufacturer:
MOT
Quantity:
3 450
Part Number:
ATmega8515-16AC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL
Quantity:
4 500
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16PU
Manufacturer:
AT
Quantity:
20 000
The X-register, Y-register, and
Z-register
Stack Pointer
12
ATmega8515(L)
The registers R26..R31 have some added functions to their general purpose usage.
These registers are 16-bit address pointers for indirect addressing of the Data Space.
The three indirect address registers X, Y, and Z are defined as described in Figure 5.
Figure 5. The X-, Y-, and Z-registers
In the different addressing modes these address registers have functions as fixed dis-
placement, automatic increment, and automatic decrement (see the Instruction Set
reference for details).
The Stack is mainly used for storing temporary data, for storing local variables and for
storing return addresses after interrupts and subroutine calls. The Stack Pointer Regis-
ter always points to the top of the Stack. Note that the Stack is implemented as growing
from higher memory locations to lower memory locations. This implies that a Stack
PUSH command decreases the Stack Pointer.
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Inter-
rupt Stacks are located. This Stack space in the data SRAM must be defined by the
program before any subroutine calls are executed or interrupts are enabled. The Stack
Pointer must be set to point above $60. The Stack Pointer is decremented by one when
data is pushed onto the Stack with the PUSH instruction, and it is decremented by two
when the return address is pushed onto the Stack with subroutine call or interrupt. The
Stack Pointer is incremented by one when data is popped from the Stack with the POP
instruction, and it is incremented by two when address is popped from the Stack with
return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The num-
ber of bits actually used is implementation dependent. Note that the data space in some
implementations of the AVR architecture is so small that only SPL is needed. In this
case, the SPH Register will not be present.
X-register
Y-register
Z-register
Bit
Read/Write
Initial Value
SP15
SP7
R/W
R/W
15
7
0
0
15
7
R27 ($1B)
15
7
R29 ($1D)
15
7
R31 ($1F)
SP14
SP6
R/W
R/W
14
6
0
0
SP13
SP5
R/W
R/W
13
5
0
0
XH
YH
ZH
0
SP12
SP4
R/W
R/W
12
4
0
0
SP11
SP3
R/W
R/W
11
3
0
0
0
0
7
R26 ($1A)
7
R28 ($1C)
7
R30 ($1E)
SP10
R/W
R/W
SP2
10
2
0
0
R/W
R/W
SP9
SP1
9
1
0
0
XL
YL
ZL
0
R/W
R/W
SP8
SP0
2512K–AVR–01/10
8
0
0
0
SPH
SPL
0
0
0
0
0