ATmega32C1 Automotive Atmel Corporation, ATmega32C1 Automotive Datasheet - Page 49

no-image

ATmega32C1 Automotive

Manufacturer Part Number
ATmega32C1 Automotive
Description
Manufacturer
Atmel Corporation

Specifications of ATmega32C1 Automotive

Flash (kbytes)
32 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
27
Ext Interrupts
27
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Can
1
Lin
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
125
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 150
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes
7.2.3
7647G–AVR–09/11
Brown-out Detection
ATmega16/32/64/M1/C1 has an On-chip Brown-out Detection (BOD) circuit for monitoring the
V
can be selected by the BODLEVEL Fuses. The trigger level has a hysteresis to ensure spike
free Brown-out Detection. The hysteresis on the detection level should be interpreted as V
= V
Table 7-2.
Notes:
Table 7-3.
Notes:
When the BOD is enabled, and V
ure 7-5 on page
above the trigger level (V
after the Time-out period t
The BOD circuit will only detect a drop in V
ger than t
Symbol
V
t
CC
BOD
HYST
BOT
level during operation by comparing it to a fixed trigger level. The trigger level for the BOD
+ V
1. V
2. Values are guidelines only.
1. Values are guidelines only.
BOD
HYST
where this is the case, the device is tested down to V
This guarantees that a Brown-Out Reset will occur before V
rect operation of the microcontroller is no longer guaranteed. The test is performed using
BODLEVEL = 010 for Low Operating Voltage and BODLEVEL = 101 for High Operating
Voltage .
BOT
given in
BODLEVEL Fuse Coding
Brown-out Characteristics
Parameter
Brown-out Detector Hysteresis
Min Pulse Width on Brown-out Reset
/2 and V
BODLEVEL 2..0 Fuses
may be below nominal minimum operating voltage for some devices. For devices
50), the Brown-out Reset is immediately activated. When V
Table
BOT-
111
110
011
100
010
001
101
000
TOUT
BOT+
= V
7-3.
has expired.
BOT
in
CC
Figure 7-5 on page
- V
decreases to a value below the trigger level (V
Atmel ATmega16/32/64/M1/C1
HYST
(1)(2)
(1)
/2.
CC
if the voltage stays below the trigger level for lon-
50), the delay counter starts the MCU
Min.
CC
Typ V
Disabled
= V
4.5
4.4
4.3
4.2
2.8
2.7
2.6
CC
Typ.
BOT
BOT
80
2
drops to a voltage where cor-
during the production test.
Max.
CC
Units
BOT-
increases
V
V
V
V
V
V
V
Units
mV
in
µs
BOT+
Fig-
49

Related parts for ATmega32C1 Automotive