ATmega328P Automotive Atmel Corporation, ATmega328P Automotive Datasheet - Page 248
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega328P Automotive
Manufacturer Part Number
ATmega328P Automotive
Description
Manufacturer
Atmel Corporation
Specifications of ATmega328P Automotive
Flash (kbytes)
32 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 248 of 345
- Download datasheet (6Mb)
23.5
23.5.1
23.5.2
248
Changing Channel or Reference Selection
ATmega328P [Preliminary]
ADC Input Channels
ADC Voltage Reference
The MUXn and REFS1:0 bits in the ADMUX Register are single buffered through a temporary
register to which the CPU has random access. This ensures that the channels and reference
selection only takes place at a safe point during the conversion. The channel and reference
selection is continuously updated until a conversion is started. Once the conversion starts, the
channel and reference selection is locked to ensure a sufficient sampling time for the ADC. Con-
tinuous updating resumes in the last ADC clock cycle before the conversion completes (ADIF in
ADCSRA is set). Note that the conversion starts on the following rising ADC clock edge after
ADSC is written. The user is thus advised not to write new channel or reference selection values
to ADMUX until one ADC clock cycle after ADSC is written.
If Auto Triggering is used, the exact time of the triggering event can be indeterministic. Special
care must be taken when updating the ADMUX Register, in order to control which conversion
will be affected by the new settings.
If both ADATE and ADEN is written to one, an interrupt event can occur at any time. If the
ADMUX Register is changed in this period, the user cannot tell if the next conversion is based
on the old or the new settings. ADMUX can be safely updated in the following ways:
When updating ADMUX in one of these conditions, the new settings will affect the next ADC
conversion.
When changing channel selections, the user should observe the following guidelines to ensure
that the correct channel is selected:
In Single Conversion mode, always select the channel before starting the conversion. The chan-
nel selection may be changed one ADC clock cycle after writing one to ADSC. However, the
simplest method is to wait for the conversion to complete before changing the channel selection.
In Free Running mode, always select the channel before starting the first conversion. The chan-
nel selection may be changed one ADC clock cycle after writing one to ADSC. However, the
simplest method is to wait for the first conversion to complete, and then change the channel
selection. Since the next conversion has already started automatically, the next result will reflect
the previous channel selection. Subsequent conversions will reflect the new channel selection.
The reference voltage for the ADC (V
ended channels that exceed V
either AV
AV
ated from the internal bandgap reference (V
external AREF pin is directly connected to the ADC, and the reference voltage can be made
more immune to noise by connecting a capacitor between the AREF pin and ground. V
also be measured at the AREF pin with a high impedance voltmeter. Note that V
impedance source, and only a capacitive load should be connected in a system.
CC
a. When ADATE or ADEN is cleared.
b. During conversion, minimum one ADC clock cycle after the trigger event.
c. After a conversion, before the Interrupt Flag used as trigger source is cleared.
is connected to the ADC through a passive switch. The internal 1.1V reference is gener-
CC
, internal 1.1V reference, or external AREF pin.
REF
will result in codes close to 0x3FF. V
REF
) indicates the conversion range for the ADC. Single
BG
) through an internal amplifier. In either case, the
REF
can be selected as
7810A–AVR–11/09
REF
is a high
REF
can
Related parts for ATmega328P Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega328P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![atmega328p-20mu](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Atmega88p 8-bit Microcontroller With 8k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA328P/V](/images/no-image3.png)
Part Number:
Description:
8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATMEGA328-MU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-AU](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATmega328](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA328-PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 28PDIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-MMHR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 16KB FL 512B EE 1KB SRAM 20 MHZ GRN
Manufacturer:
Atmel
![ATMEGA328-AUR](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32QFN
Manufacturer:
Atmel
Datasheet:
![A000046](/photos/15/92/159298/arduinounofront_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools Uno
Manufacturer:
Arduino
Datasheet:
![A000048](/photos/18/99/189989/4243185_tmb.jpg)
Part Number:
Description:
ATMEGA328 MCU IC W/ Arduino UNO Bootloader
Manufacturer:
Arduino
Datasheet:
![A000004](/photos/36/49/364973/arduino_mini_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools MINI LITE
Manufacturer:
Arduino
Datasheet:
![A000003](/photos/36/49/364973/arduino_mini_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools MINI
Manufacturer:
Arduino
Datasheet: