ATmega328P Automotive Atmel Corporation, ATmega328P Automotive Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega328P Automotive
Manufacturer Part Number
ATmega328P Automotive
Description
Manufacturer
Atmel Corporation
Specifications of ATmega328P Automotive
Flash (kbytes)
32 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- Current page: 14 of 345
- Download datasheet (6Mb)
6.7
Reset and Interrupt Handling
The AVR provides several different interrupt sources. These interrupts and the separate Reset
Vector each have a separate program vector in the program memory space. All interrupts are
assigned individual enable bits which must be written logic one together with the Global Interrupt
Enable bit in the Status Register in order to enable the interrupt. Depending on the Program
Counter value, interrupts may be automatically disabled when Boot Lock bits BLB02 or BLB12
are programmed. This feature improves software security. See the section
“Memory Program-
ming” on page 286
for details.
The lowest addresses in the program memory space are by default defined as the Reset and
Interrupt Vectors. The complete list of vectors is shown in
“Interrupts” on page
56. The list also
determines the priority levels of the different interrupts. The lower the address the higher is the
priority level. RESET has the highest priority, and next is INT0 – the External Interrupt Request
0. The Interrupt Vectors can be moved to the start of the Boot Flash section by setting the IVSEL
bit in the MCU Control Register (MCUCR). Refer to
“Interrupts” on page 56
for more information.
The Reset Vector can also be moved to the start of the Boot Flash section by programming the
BOOTRST Fuse, see
“Boot Loader Support – Read-While-Write Self-Programming,
ATmega88P, ATmega168P and ATmega328P” on page
271.
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared and all interrupts are dis-
abled. The user software can write logic one to the I-bit to enable nested interrupts. All enabled
interrupts can then interrupt the current interrupt routine. The I-bit is automatically set when a
Return from Interrupt instruction – RETI – is executed.
There are basically two types of interrupts. The first type is triggered by an event that sets the
Interrupt Flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vec-
tor in order to execute the interrupt handling routine, and hardware clears the corresponding
Interrupt Flag. Interrupt Flags can also be cleared by writing a logic one to the flag bit position(s)
to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is
cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is
cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt
Enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the
Global Interrupt Enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These
interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the
interrupt is enabled, the interrupt will not be triggered.
When the AVR exits from an interrupt, it will always return to the main program and execute one
more instruction before any pending interrupt is served.
Note that the Status Register is not automatically stored when entering an interrupt routine, nor
restored when returning from an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled.
No interrupt will be executed after the CLI instruction, even if it occurs simultaneously with the
CLI instruction. The following example shows how this can be used to avoid interrupts during the
timed EEPROM write sequence.
ATmega328P [Preliminary]
14
7810A–AVR–11/09
Related parts for ATmega328P Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega328P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![atmega328p-20mu](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Atmega88p 8-bit Microcontroller With 8k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA328P/V](/images/no-image3.png)
Part Number:
Description:
8-bit Microcontroller with 4/8/16/32K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATMEGA328-MU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-AU](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATmega328](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA328-PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 28PDIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-MMHR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 16KB FL 512B EE 1KB SRAM 20 MHZ GRN
Manufacturer:
Atmel
![ATMEGA328-AUR](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA328-MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 32K FLASH 32QFN
Manufacturer:
Atmel
Datasheet:
![A000046](/photos/15/92/159298/arduinounofront_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools Uno
Manufacturer:
Arduino
Datasheet:
![A000048](/photos/18/99/189989/4243185_tmb.jpg)
Part Number:
Description:
ATMEGA328 MCU IC W/ Arduino UNO Bootloader
Manufacturer:
Arduino
Datasheet:
![A000004](/photos/36/49/364973/arduino_mini_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools MINI LITE
Manufacturer:
Arduino
Datasheet:
![A000003](/photos/36/49/364973/arduino_mini_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools MINI
Manufacturer:
Arduino
Datasheet: