AT90PWM2B Atmel Corporation, AT90PWM2B Datasheet - Page 300

• Manufacturer Part Number: AT90PWM2B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM2B

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

T
Note:
300
A
Symbol
I
V
V
I
t
CC
ACLK
ACID
ACIO
hysr
= -40°C to +105°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at Vcc = 5V, 10 mA at Vcc = 3V) under steady state
AT90PWM2/3/2B/3B
conditions (non-transient), the following must be observed:
SO32, SO24 and TQFN Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 100 mA.
4] The sum of all IOL, for ports B3 - B5, C6 - C7 should not exceed 100 mA.
5] The sum of all IOL, for ports B2, C4 - C5, D5 - D7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
SO32, SO24 and TQFN Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports B6 - B7, C0 - C1, D0 - D3, E0 should not exceed 150 mA.
3] The sum of all IOH, for ports B0 - B1, C2 - C3, D4, E1 - E2 should not exceed 150 mA.
4] The sum of all IOH, for ports B3 - B5, C6 - C7 should not exceed 150 mA.
5] The sum of all IOH, for ports B2, C4 - C5, D5 - D7 should not exceed 150 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
AT90PWM2/3
Analog Comparator
Hysteresis Voltage
AT90PWM2B/3B
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
Parameter
CC
= 2.7V to 5.5V (unless otherwise noted) (Continued)
(5)
Condition
Active 8 MHz, V
RC osc, PRR = 0xFF
Active 16 MHz, V
Ext Clock, PRR = 0xFF
Idle 8 MHz, V
Osc
Idle 16 MHz, V
Ext Clock
WDT enabled, V
t0 < 90°C
WDT enabled, V
t0 < 105°C
WDT disabled, V
t0 < 90°C
WDT disabled, V
t0 < 105°C
V
V
Rising Edge
Falling Edge
V
V
V
V
CC
CC
CC
in
CC
CC
= V
= 5V, V
= 5V, V
= 5V
= 2.7V
= 5.0V
CC
/2
in
in
CC
= 3V
= 3V
CC
CC
= 3V, RC
CC
CC
CC
CC
CC
= 5V,
= 3V,
= 3V
= 3V
= 3V
= 3V
= 5V,
Min.
-50
33
34
CC
= 5V, 10 mA at V
Typ.
3.8
1.5
5.5
14
20
46
62
(6)
(6)
5
9
2
5
CC
Max.
110
24
10
15
20
10
71
50
50
7
3
3
= 3V) under steady state
4317J–AVR–08/10
Units
mA
mA
mA
mA
mV
mV
mV
µA
µA
µA
µA
nA
ns