AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 165

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

4378C–AVR–09/08
This feature is useful to detect that a PSC output doesn’t change due to a freezen external input
signal.
• Bit 5 – PSEIn : PSC n Synchro Error Interrupt
This bit is set by hardware when the update (or end of PSC cycle) of the PSCn configured in
auto run (PARUNn = 1) does not occur at the same time than the PSCn-1 which has generated
the input run signal. (For PSC0, PSCn-1 is PSC2).
Must be cleared by software by writing a one to its location.
This feature is useful to detect that a PSC doesn’t run at the same speed or with the same phase
than the PSC master.
• Bit 4 – PEVnB : PSC n External Event B Interrupt
This bit is set by hardware when an external event which can generates a capture or a retrigger
from Retrigger/Fault block B occurs.
Must be cleared by software by writing a one to its location.
This bit can be read even if the corresponding interrupt is not enabled (PEVEnB bit = 0).
• Bit 3 – PEVnA : PSC n External Event A Interrupt
This bit is set by hardware when an external event which can generates a capture or a retrigger
from Retrigger/Fault block A occurs.
Must be cleared by software by writing a one to its location.
This bit can be read even if the corresponding interrupt is not enabled (PEVEnA bit = 0).
• Bit 2:1 – PRNn1:0 : PSC n Ramp Number
Memorization of the ramp number when the last PEVnA or PEVnB occured.
Table 50. PSC n Ramp Number Description
• Bit 0 – PEOPn: End Of PSC n Interrupt
This bit is set by hardware when PSC n achieves its whole cycle.
Must be cleared by software by writing a one to its location.
PRNn1
0
0
1
1
PRNn0
0
1
0
1
Description
The last event which has generated an interrupt occured during ramp 1
The last event which has generated an interrupt occured during ramp 2
The last event which has generated an interrupt occured during ramp 3
The last event which has generated an interrupt occured during ramp 4
AT90PWM1
165