AT89C5131A-M Atmel Corporation, AT89C5131A-M Datasheet - Page 97
AT89C5131A-M
Manufacturer Part Number
AT89C5131A-M
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT89C5130A-M.pdf
(188 pages)
2.AT89C5130A-M.pdf
(4 pages)
3.AT89C5130A-M.pdf
(34 pages)
Specifications of AT89C5131A-M
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
48 MHz
Cpu
8051-12C
Max I/o Pins
34
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
1
Sram (kbytes)
1.25
Eeprom (bytes)
1024
Self Program Memory
API
Operating Voltage (vcc)
2.7 to 5.5
Timers
4
Isp
UART/USB
Watchdog
Yes
- Current page: 97 of 188
- Download datasheet (2Mb)
Figure 19-4. Data Transmission Format (CPHA = 0)
Figure 19-5. Data Transmission Format (CPHA = 1)
Figure 19-6. CPHA/SS Timing
4337K–USB–04/08
MOSI (from Master)
SCK cycle number
MISO (from Slave)
MOSI (from Master)
SCK (CPOL = 0)
SCK (CPOL = 1)
MISO (from Slave)
SCK cycle number
SPEN (internal)
SCK (CPOL = 0)
SCK (CPOL = 1)
Capture point
SPEN (internal)
SS (to Slave)
Capture point
SS (to Slave)
output data are shifted (Figure 19-4 and Figure 19-5). The clock phase and polarity should be
identical for the Master SPI device and the communicating Slave device.
As shown in
must begin driving its data before the first SCK edge, and a falling edge on the SS pin is used to
start the transmission. The SS pin must be toggled high and then low between each byte trans-
mitted (Figure 19-2).
Figure 19-6
ing its MOSI pin on the first SCK edge. Therefore the Slave uses the first SCK edge as a start
transmission signal. The SS pin can remain low between transmissions
mat may be preferable in systems having only one Master and only one Slave driving the MISO
data line.
MISO/MOSI
(CPHA = 0)
(CPHA = 1)
Master SS
Slave SS
Slave SS
shows an SPI transmission in which CPHA is’1’. In this case, the Master begins driv-
Figure
MSB
MSB
MSB
1
MSB
1
19-5, the first SCK edge is the MSB capture strobe. Therefore the Slave
2
bit6
bit6
2
bit6
Byte 1
bit6
3
bit5
bit5
3
bit5
bit5
bit4
4
bit4
bit4
4
bit4
Byte 2
bit3
bit3
5
bit3
bit3
5
6
bit2
bit2
6
bit2
bit2
Byte 3
7
bit1
bit1
7
bit1
AT89C5130A/31A-M
bit1
LSB
8
LSB
LSB
8
LSB
(Figure
19-1). This for-
97
Related parts for AT89C5131A-M
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit microcontroller with 4K bytes flash, 5V, 20MHz
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Microcontroller With 4k Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC 8051 MCU 64K FLASH 44-VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 24SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 16K 32VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 32K 64BGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 52PLCC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU FLASH 64K 64VQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU 16K FLASH 32-VQFP
Manufacturer:
Atmel
Datasheet: