AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 94

• Manufacturer Part Number: AT32UC3B1128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B1128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

12.2.4
32059L–AVR32–01/2012
Rev. B
- PWM
1. PWM channel interrupt enabling triggers an interrupt
2. PWN counter restarts at 0x0001
3. PWM update period to a 0 value does not work
4. PWM channel status may be wrong if disabled before a period has elapsed
5. The following alternate C functions PWM[4] on PA16 and PWM[6] on PA31 are not
6. SPI
7. SPI Slave / PDCA transfer: no TX UNDERRUN flag
When enabling a PWM channel that is configured with center aligned period (CALG=1), an
interrupt is signalled.
Fix/Workaround
When using center aligned mode, enable the channel and read the status before channel
interrupt is enabled.
The PWM counter restarts at 0x0001 and not 0x0000 as specified. Because of this the first
PWM period has one more clock cycle.
Fix/Workaround
- The first period is 0x0000, 0x0001, ..., period.
- Consecutive periods are 0x0001, 0x0002, ..., period.
It is impossible to update a period equal to 0 by the using the PWM update register
(PWM_CUPD).
Fix/Workaround
Do not update the PWM_CUPD register with a value equal to 0.
Before a PWM period has elapsed, the read channel status may be wrong. The CHIDx-bit
for a PWM channel in the PWM Enable Register will read '1' for one full PWM period even if
the channel was disabled before the period elapsed. It will then read '0' as expected.
Fix/Workaround
Reading the PWM channel status of a disabled channel is only correct after a PWM period
has elapsed.
available on Rev B
The following alternate C functions PWM[4] on PA16 and PWM[6] on PA31 are not available
on Rev B.
Fix/Workaround
Do not use these PWM alternate functions on these pins.
There is no TX UNDERRUN flag available, therefore in SPI slave mode, there is no way to
be informed of a character lost in transmission.
Fix/Workaround
For PDCA transfer: none.
94