AT32UC3B1128 Atmel Corporation, AT32UC3B1128 Datasheet - Page 83

• Manufacturer Part Number: AT32UC3B1128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B1128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 28
• Ext Interrupts: 28
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32059L–AVR32–01/2012
- TC
2. Transfer error will stall a transmit peripheral handshake interface
3. TWI
4. The TWI RXRDY flag in SR register is not reset when a software reset is performed
5. TWI in master mode will continue to read data
6. TWI slave behaves improperly if master acknowledges the last transmitted data byte
7. GPIO
8. PA29 (TWI SDA) and PA30 (TWI SCL) GPIO VIH (input high voltage) is 3.6V max
1. Channel chaining skips first pulse for upper channel
If a transfer error is encountered on a channel transmitting to a peripheral, the peripheral
handshake of the active channel will stall and the PDCA will not do any more transfers on
the affected peripheral handshake interface.
Fix/Workaround
Disable and then enable the peripheral after the transfer error.
The TWI RXRDY flag in SR register is not reset when a software reset is performed.
Fix/Workaround
After a Software Reset, the register TWI RHR must be read.
TWI in master mode will continue to read data on the line even if the shift register and the
RHR register are full. This will generate an overrun error.
Fix/Workaround
To prevent this, read the RHR register as soon as a new RX data is ready.
before a STOP condition
In I2C slave transmitter mode, if the master acknowledges the last data byte before a STOP
condition (what the master is not supposed to do), the following TWI slave receiver mode
frame may contain an inappropriate clock stretch. This clock stretch can only be stopped by
resetting the TWI.
Fix/Workaround
If the TWI is used as a slave transmitter with a master that acknowledges the last data byte
before a STOP condition, it is necessary to reset the TWI before entering slave receiver
mode.
instead of 5V tolerant
The following GPIOs are not 5V tolerant: PA29 and PA30.
Fix/Workaround
None.
When chaining two channels using the Block Mode Register, the first pulse of the clock
between the channels is skipped.
Fix/Workaround
Configure the lower channel with RA = 0x1 and RC = 0x2 to produce a dummy clock cycle
for the upper channel. After the dummy cycle has been generated, indicated by the
SR.CPCS bit, reconfigure the RA and RC registers for the lower channel with the real
values.
83