AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 851

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

• CSTOE: Completion Signal Time-out Error
• DTOE: Data Time-out Error
• DCRCE: Data CRC Error
• RTOE: Response Time-out Error
• RENDE: Response End Bit Error
• RCRCE: Response CRC Error
• RDIRE: Response Direction Error
• RINDE: Response Index Error
• TXBUFE: TX Buffer Empty Status
• RXBUFF: RX BUffer Full Status
• CSRCV: CE-ATA Completion Signal Received
• SDIOWAIT: SDIO Read Wait Operation Status
• SDIOIRQB: SDIO Interrupt for Slot B
• SDIOIRQA: SDIO Interrupt for Slot A
• ENDTX: End of RX Buffer
• ENDRX: End of RX Buffer
• NOTBUSY: MCI Not Busy
32072G–11/2011
This bit is set when the completion signal time-out defined by the CSTOR.CSTOCYC field and the CSTOR.CSTOMUL field is
reached.
This bit is cleared when reading the SR register.
This bit is set when the data time-out defined by the DTOR.DTOCYC field and the DTOR.DTOMUL field is reached.
This bit is cleared when reading the SR register.
This bit is set when a CRC16 error is detected in the last data block.
This bit is cleared when reading the SR register.
This bit is set when the response time-out defined by the CMDR.MAXLAT bit is reached.
This bit is cleared when writing the CMDR register.
This bit is set when the end bit of the response is not detected.
This bit is cleared when writing the CMDR register.
This bit is set when a CRC7 error is detected in the response.
This bit is cleared when writing the CMDR register.
This bit is set when the direction bit from card to host in the response is not detected.
This bit is cleared when writing the CMDR register.
This bit is set when a mismatch is detected between the command index sent and the response index received.
This bit is cleared when writing the CMDR register.
This bit is set when the DMA Tx Buffer is empty.
This bit is cleared when the DMA Tx Buffer is not empty.
This bit is set when the DMA Rx Buffer is full.
This bit is cleared when the DMA Rx Buffer is not full.
This bit is set when the device issues a command completion signal on the command line.
This bit is cleared when reading the SR register.
This bit is set when the data bus has entered IO wait state.
This bit is cleared when normal bus operation.
This bit is cleared when reading the SR register.
This bit is set when a SDIO interrupt on Slot B occurs.
This bit is set when a SDIO interrupt on Slot A occurs.
This bit is cleared when reading the SR register.
This bit is set when the DMA Controller transmission is finished.
This bit is cleared when the DMA Controller transmission is not finished.
This bit is set when the DMA Controller reception is finished.
This bit is cleared when the DMA Controller reception is not finished.
This bit must be used only for write operations.
851