TDF8590TH/N1,118 NXP Semiconductors, TDF8590TH/N1,118 Datasheet - Page 9

• Manufacturer Part Number: TDF8590TH/N1,118
• Description: IC AMP AUDIO PWR 160W D 24HSOP
• Manufacturer: NXP Semiconductors
• Type: Class Dr

Specifications of TDF8590TH/N1,118

• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Package / Case: 24-HSOP
• Max Output Power X Channels @ Load: 160W x 1 @ 8 Ohm; 80W x 2 @ 4 Ohm
• Voltage - Supply: ±14 V ~ 29 V
• Features: Depop, Differential Inputs, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Product: Class-D
• Output Power: 160 W
• Available Set Gain: 32 dB
• Common Mode Rejection Ratio (min): 75 dB
• Thd Plus Noise: 0.15 %
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 8 Ohms
• Dual Supply Voltage: +/- 27 V
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential, Single
• Supply Type: Dual
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935278835118; TDF8590TH/N1-T; TDF8590TH/N1-T

NXP Semiconductors
TDF8590TH_2
Product data sheet
6.5 Diagnostic output
6.6 Differential inputs
[3]
[4]
Pin DIAG is pulled LOW when the OCP is triggered. With a continuous shorted load a
switching pattern in the voltage on pin DIAG is observed (see
LOW on pin DIAG indicates a short to the supply lines whereas a shorted load causes a
switching DIAG pin (see
The pin DIAG reference voltage is V
pull-up. An example of a circuit to read out and level shift the diagnostic data is given in
Figure
microprocessor that reads out the DIAG data.
For a high Common Mode Rejection Ratio (CMRR) and a maximum of flexibility in the
application, the audio inputs are fully differential. By connecting the inputs anti-parallel the
phase of one of the channels can be inverted, so that a load can be connected between
the two output filters. In this case the system operates as a mono BTL amplifier.
The input configuration for a mono BTL application is illustrated in
In the stereo SE configuration it is also recommended to connect the two differential
inputs in anti-phase. This has advantages for the current handling of the power supply at
low signal frequencies (supply pumping).
Fig 7. DIAG readout circuit with level shift
Only complete shut down of amplifier in case of a short-circuit. In all other cases current limiting resulting in
clipping output signal.
Fault condition detected during (every) transition between standby-to-mute and during restart after
activation of OCP (short to one of the supply lines).
7. V5V represents a logic supply that is used in the application by the
Rev. 02 — 23 April 2007
Section
V
DIAG
V
DDA
SSA
2
80 W SE (4 ) or 1
6.4.3).
100 k
SSA
. Pin DIAG should not be connected to an external
5.6 V
M1
100 k
27 k
SGND
V5V
160 W BTL (8 ) class-D amplifier
M2
10 k
001aad840
DIAG
out
Figure
TDF8590TH
Figure
6). A permanent
© NXP B.V. 2007. All rights reserved.
8.
9 of 30