TDF8590TH/N1S,118 NXP Semiconductors, TDF8590TH/N1S,118 Datasheet - Page 16

• Manufacturer Part Number: TDF8590TH/N1S,118
• Description: IC PWR AMP AUDIO CLASS D 24HSOP
• Manufacturer: NXP Semiconductors
• Type: Class Dr

Specifications of TDF8590TH/N1S,118

• Output Type: 1-Channel (Mono) or 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 160W x 1 @ 8 Ohm; 80W x 2 @ 4 Ohm
• Voltage - Supply: ±14 V ~ 29 V
• Features: Depop, Differential Inputs, Mute, Short-Circuit and Thermal Protection, Standby
• Mounting Type: Surface Mount
• Package / Case: 24-HSOP
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS compliant by exemption
• Other names: 935289143118

NXP Semiconductors
TDF8590TH_2
Product data sheet
12.3 External clock
12.4 Noise
Peak output current, internally limited to 8 A:
SE:
BTL:
Variables:
I
and the ripple current. The value of the ripple current is dependent on the coil inductance
and voltage drop over the coil.
If two or more class-D amplifiers are used it is recommended that all devices run at the
same switching frequency. This can be realized by connecting all OSC pins together and
feed them from an external oscillator.
The internal oscillator requires an external R
V
above SGND. The internal oscillator is disabled and the PWM modulator will switch with
the external frequency. The duty cycle of the external clock should be between 47.5 %
and 52.5 %.
The noise contribution of the internal oscillator is supply voltage dependent. In low noise
applications running at high supply voltage an external low noise oscillator is
recommended.
Noise should be measured using a high-order low-pass filter with a cut-off frequency of
20 kHz. The standard audio band pass filters used in audio analyzers do not suppress the
residue of the carrier frequency sufficiently to ensure a reliable measurement of the
audible noise. Noise measurements should preferably be carried out using AES 17 (Brick
Wall) filters or the Audio Precision AUX 0025 filter, which was designed especially for
measuring switching (class-D) amplifiers.
OM
SSA
R
R
R
R
f
t
V
P
osc
w(min)
P
o(0.5%)
L
s(L)
DSon(hs)
DSon(ls)
should be below 8 A (see
I
. For application of an external oscillator it is necessary to force OSC to a DC level
= load resistance
= supply voltage [or 0.5 (V
OM
I
= oscillator frequency
OM
= series resistance of the filter coil
= minimum pulse width (typical 150 ns, temperature dependent)
=
= output power at the onset of clipping
=
= low side drain source on-state resistance (temperature dependent)
= high side drain source on-state resistance (temperature dependent)
V
----------------------------------------------------------- -
R
-------------------------------------------------------------------------------------------
R
P
L
L
+
+
R
1 t
2V
R
DSon hs
–
DSon hs
P
w min
–
Rev. 02 — 23 April 2007
1 t
+
–
2
+
R
w min
R
Section
f
s L
osc
80 W SE (4 ) or 1
DSon ls
DD
+ V
A
f
SS
7). I
osc
+
)]
2R
OM
ext(OSC)
s L
is the sum of the current through the load
A
and C
160 W BTL (8 ) class-D amplifier
ext(OSC)
TDF8590TH
between pins OSC and
© NXP B.V. 2007. All rights reserved.
16 of 30