MT9M001C12STM-EVAL Micron Technology Inc, MT9M001C12STM-EVAL Datasheet - Page 25

• Manufacturer Part Number: MT9M001C12STM-EVAL
• Manufacturer: Micron Technology Inc

Specifications of MT9M001C12STM-EVAL

• Lead Free Status / Rohs Status: Compliant

Registers
Table 9:
PDF: 09005aef81c2856f/Source: 09005aef80a3e031
MT9M001_DS_2.fm - Rev. F 5/06 EN
Reg0x5F
This register controls the operation of the black level calibration thresholds.
Reg0x62
This register is used to control the automatic black level calibration circuitry.
Register
Black Level Registers
14:8
10:3
bit
5:0
2:1
15
15
14
13
12
11
7
0
Description
No gain dependence.
1 = Thres_lo is set by the programmed value of bits 5:0, Thres_hi is reset to the programmed value
(bits 14:8) after every black level average restart.
0 = Thres_lo and Thres_hi are set automatically as described below.
Thres_hi
Black level maximum is set to this value when bit 7 = 1, black level maximum is reset to this value
after every black level average restart if bit 15 = 1 and bit 7 = 0.
1 = override automatic Thres_hi and Thres_lo adjust (Thres_hi always = bits 14:8, Thres_lo always =
bits 5:0).
Thres_lo
Under default automatic operation (bit 7 = 0, bit 15 = 0), Thres_lo = RegGain
bit 6 +1) x (RegGain
register settings.
Whenever a jump in the calibration causes the black level data to change from below Thres_lo to
above Thres_hi, Thres_hi is adjusted according to the following:
If new black level < 64: Thres_hi = Thres_lo + 2 + (2 x Delta), where Delta = new black level -
After any recalculation of the black level and average restart, Thres_hi is reset to either Thres_lo +
5 (automatic, default mode), Thres_hi (bit 7 = 1). Reg0x62, bit 11 will override this.
1 = do not perform the rapid black level sweep on new gain settings.
0 = normal operation.
1 = start a new running digitally filtered average for the black level (this is internally reset to “0”
immediately), and do a rapid sweep to find the new starting point.
1 = do not reset the upper threshold after a black level recalculation sweep.
0 = reset the upper threshold after a black level recalculation sweep (default).
Reserved
Force/disable black level calibration.
00 = apply black level calibration during ADC operation only (default).
X1 = disable black level correction (Offset Correction Voltage = Skew Voltage = 0.0V).
(In this case, no black level correction is possible).
Manual override of black level correction.
1 = override automatic black level correction with programmed values.
0 = normal operation (default).
Reserved
Reserved
10 = apply black level calibration continuously.
0 = automatic Thres_hi and Thres_lo adjustment.
If new black level > 63 and < 119: Thres_hi = new black level + 4
If new black level > 119: Thres_hi = 123
—
—
Thres_lo
—
—
—
maximum allowed black level in ADC LSBs (default = Thres_lo + 5).
Lower threshold for black level in ADC LSBs.
default is 1; do not change.
default is 0; do not change.
default is 0; do not change.
max
, bit 7 +1), where RegGain
MT9M001: 1/2-Inch Megapixel Digital Image Sensor
25
Micron Technology, Inc., reserves the right to change products or specifications without notice.
max
is the maximum of the four independent gain
©2004 Micron Technology, Inc. All rights reserved.
max
/4 x (RegGain
Registers
max
,