ST7538Q STMicroelectronics, ST7538Q Datasheet - Page 36

IC TXRX FSK POWER LINE 44-TQFP

ST7538Q

Manufacturer Part Number
ST7538Q
Description
IC TXRX FSK POWER LINE 44-TQFP
Manufacturer
STMicroelectronics
Type
Transceiverr
Datasheet

Specifications of ST7538Q

Number Of Drivers/receivers
1/1
Voltage - Supply
4.75 V ~ 5.25 V
Mounting Type
Surface Mount
Package / Case
44-TQFP Exposed Pad, 44-eTQFP, 44-HTQFP, 44-VQFP
For Use With
497-5484 - BOARD EVAL ST7538 PWR LINE TXRX
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Protocol
-
Other names
497-5525

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ST7538Q
Manufacturer:
STMicroelectronics
Quantity:
135
Part Number:
ST7538Q
Manufacturer:
QFP
Quantity:
513
Part Number:
ST7538Q
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
ST7538Q
Manufacturer:
ST
0
Part Number:
ST7538Q ST TQFP44
Manufacturer:
ST
0
Part Number:
ST7538QTR
Quantity:
2 000
Part Number:
ST7538QTR
Manufacturer:
STM
Quantity:
2 495
Part Number:
ST7538QTR
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
ST7538QTR
Manufacturer:
ST
0
Auxiliary analog and digital functions
6
6.1
6.2
6.3
36/44
Auxiliary analog and digital functions
Band in use
The Band in Use Block has a Carrier Detection like function but with a different Input
Sensibility (77dBµV Typ.)
and with a different BandPass filter Selectivity (40dB/Dec).
BU line is forced High when a signal in band is detected.
To prevent BU line false transition, BU signal is conditioned to Carrier Detection Internal
Signal.
Time out
Time Out Function is a protection against a too long data transmission. When Time Out
function is enabled after 1 or 3 second of continuos transmission the transceiver is forced in
receiving mode. This function allows ST7538Q to automatically manage the CENELEC
Medium Access specification. When a time-out event occur, TOUT is forced high, and is
held high for at least 125 ms. To Unlock the Time Out condition RxTx should be forced High.
During the time out period only register access or reception mode are enabled.
During Reset sequence if RxTx line =”0” & REG_DATA line =”0”, TIMEOUT protection is
suddendly enabled and ST7538Q must be configured in data reception after the reset event
before starting a new data transmission.
Time Out time is programmable using Control Register bits 7 and 8
Figure 20. Time-out timing and unlock sequence
Reset & watchdog
RSTO Output is a reset generator for the application circuitry. During the ST7538Q startup
sequence is forced low. RSTO becomes high after a T
startup sequence.
Inside ST7538Q is also embedded a watchdog function. The watchdog function is used to
detect the occurrence of a software fault of the Host Controller. The watchdog circuitry
generates an internal and external reset (RSTO low for T
watchdog timer. The watchdog timer reset can be achieved applying a negative pulse on
WD pin
(Figure
Time Out function
21).
RxTx
T
OUT
T
OFF
RSTO
RSTO
T
OFFD
delay from the end of oscillator
time) on expiry of the internal
D03IN1409
(Table
11).
ST7538Q

Related parts for ST7538Q