PIC18F46K80-I/ML Microchip Technology Inc., PIC18F46K80-I/ML Datasheet - Page 305

• Manufacturer Part Number: PIC18F46K80-I/ML
• Description: 44 QFN 8X8X0.9MM TUBE, ECAN, 64KB FLASH, 4KB RAM, 16 MIPS, 12-BIT ADC, CTMU
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F46K80-I/ML

• A/d Inputs: 11-Channel, 12-Bit
• Comparators: 2
• Cpu Speed: 16 MIPS
• Eeprom Memory: 1K Bytes
• Input Output: 35
• Interface: I2C/SPI/UART/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin QFN
• Programmable Memory: 64K Bytes
• Ram Size: 3.6K Bytes
• Speed: 64 MHz
• Temperature Range: –40 to 125 °C
• Timers: 2-8-bit, 3-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 21-5:
 2011 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
GCEN
R/W-0
2:
Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive.
If the I
writes to the SSPBUF are disabled).
GCEN: General Call Enable bit
Unused in Master mode.
ACKSTAT: Acknowledge Status bit (Master Transmit mode only)
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
ACKDT: Acknowledge Data bit (Master Receive mode only)
1 = Not Acknowledge
0 = Acknowledge
ACKEN: Acknowledge Sequence Enable bit
1 = Initiates Acknowledge sequence on SDA and SCL pins and transmit ACKDT data bit. Automatically
0 = Acknowledge sequence Idle
RCEN: Receive Enable bit (Master Receive mode only)
1 = Enables Receive mode for I
0 = Receive Idle
PEN: Stop Condition Enable bit
1 = Initiates Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
RSEN: Repeated Start Condition Enable bit
1 = Initiates Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
SEN: Start Condition Enable bit
1 = Initiates Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
ACKSTAT
2
R/W-0
C module is active, these bits may not be set (no spooling) and the SSPBUF may not be written (or
cleared by hardware.
SSPCON2: MSSP CONTROL REGISTER 2 (I
W = Writable bit
‘1’ = Bit is set
ACKDT
R/W-0
(1)
ACKEN
(2)
(2)
2
C™
R/W-0
Preliminary
(2)
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
(2)
PIC18F66K80 FAMILY
RCEN
R/W-0
(2)
(2)
2
(1)
C™ MASTER MODE)
PEN
R/W-0
(2)
x = Bit is unknown
RSEN
R/W-0
(2)
DS39977C-page 305
SEN
R/W-0
(2)
bit 0