PIC16F631-I/P Microchip Technology Inc., PIC16F631-I/P Datasheet - Page 39

• Manufacturer Part Number: PIC16F631-I/P
• Description: MCU, 8-Bit, 1KW Flash, 64 RAM, 18 I/O, PDIP-20
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F631-I/P

• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 128 Bytes
• Input Output: 18
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 20-pin PDIP
• Programmable Memory: 1.75K Bytes
• Ram Size: 64 Bytes
• Speed: 20 MHz
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

2.2.2.2
The OPTION register, shown in Register 2-2, is a
readable and writable register, which contains various
control bits to configure:
• Timer0/WDT prescaler
• External RA2/INT interrupt
• Timer0
• Weak pull-ups on PORTA/PORTB
REGISTER 2-2:
© 2007 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
RABPU
R/W-1
OPTION Register
RABPU: PORTA/PORTB Pull-up Enable bit
1 = PORTA/PORTB pull-ups are disabled
0 = PORTA/PORTB pull-ups are enabled by individual PORT latch values
INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of RA2/INT pin
0 = Interrupt on falling edge of RA2/INT pin
T0CS: Timer0 Clock Source Select bit
1 = Transition on RA2/T0CKI pin
0 = Internal instruction cycle clock (F
T0SE: Timer0 Source Edge Select bit
1 = Increment on high-to-low transition on RA2/T0CKI pin
0 = Increment on low-to-high transition on RA2/T0CKI pin
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
PS<2:0>: Prescaler Rate Select bits
INTEDG
R/W-1
OPTION_REG: OPTION REGISTER
Bit Value
000
001
010
011
100
101
110
111
W = Writable bit
‘1’ = Bit is set
R/W-1
T0CS
PIC16F631/677/685/687/689/690
Timer0 Rate
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
R/W-1
T0SE
WDT Rate
1 : 1
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
OSC
/4)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
PSA
Note:
To achieve a 1:1 prescaler assignment for
Timer0, assign the prescaler to the WDT by
setting PSA bit of the OPTION register to
‘1’. See Section 6.3 “Timer1 Prescaler”.
R/W-1
PS2
x = Bit is unknown
R/W-1
PS1
DS41262D-page 37
R/W-1
PS0
bit 0