HS9Z-A61 IDEC Corporation, HS9Z-A61 Datasheet - Page 10

• Manufacturer Part Number: HS9Z-A61
• Description: Straight Key for Idec HS6B Safety Switch
• Manufacturer: IDEC Corporation

Specifications of HS9Z-A61

• Lead Free Status / Rohs Status: RoHS Compliant part

374
For Manual Unlocking
Spring lock type
The HS6E allows manual unlocking of the actuator to pre-check proper door
operation before wiring or turning power on, as well as for emergency use such
as a power failure.
Solenoid lock type
The HS6E can be unlocked manually in an emergency.
When using the manual unlock key
•
•
•
•
When unlocking pushing the plate inside the interlock switch
•
•
•
Caution
Before manually unlocking the interlock switch, make sure that the machine
has come to a complete stop. Manual unlocking during operation may unlock
the interlock switch before the machine stops, and the function of the interlock
switch with solenoid is lost. While the solenoid is energized, do not unlock the
switch manually (solenoid lock type).
When locking or unlocking the interlock switch manually, turn the actuator
fully using the manual unlock key supplied with the switch.
Using the interlock switch with the actuator not fully turned (less than 90°)
may cause damage to the interlock switch or operation failures (when manu-
ally unlocked, the switch will keep the main circuit disconnected and the door
unlocked).
Do not apply excessive force (0.45 N·m or more) to the manual unlock part,
otherwise the manual unlock part will become damaged.
Do not leave the manual unlock key attached to the switch during operation.
This is dangerous because the switch can always be unlocked while the
machine is in operation.
Remove the screw at the side of the interlock switch (the same side where
actuator is inserted) and insert a small screwdriver.
Push the plate inside the interlock switch toward the LED indicator using a
screwdriver until the actuator is unlocked.
Tighten the screw to a proper torque (0.3 to 0.5 N·m). Do not tighten with
excessive force, otherwise the interlock switch will be damaged. Be sure to
reinstall the screw, otherwise the waterproof capability will be lost.
UNLOCK
HS6E Series
Manual Unlock Key
(supplied with the interlock switch)
(installed on both sides)
Manual Unlocking
Normal Position
Manual Unlocking
Position
www.idec.com
Recommended Tightening Torque of Mounting Screws
•
•
•
•
•
•
•
•
Cables
•
•
•
•
•
Interlock switch: 1.0 to 1.5 N·m (three M4 screws)
Actuators: 1.0 to 1.5 N·m (two M4 screws)
The above recommended tightening torques of the mounting screws are the
values with hex socket head bolts. When other screws are used and tightened
to a smaller torque, make sure that the screws do not become loose after
mounting.
Mounting bolts are not supplied with the interlock and must be supplied by
the user.
To avoid unauthorized or unintended removal of the interlock switch and the
actuator, it is recommended that the interlock switch and the actuator are
installed in an unremovable manner, for example using special screws, rivets,
or welding the screws.
When installing the HS9Z-A62S actuator, use the mounting plate (supplied
with the actuator) on the hinged door, and secure the actuator tightly using
two M4 screws.
The mounting plate has an orientation.
Do not lose the mounting plate.
Do not fasten or loosen the gland at the bottom of the interlock switch.
When bending the cable during wiring, make sure that the cable radius is kept
at 30 mm minimum.
When wiring, make sure that water or oil does not enter from the end of the
cable.
Do not open the lid of the interlock switch. Otherwise the interlock switch will
be damaged.
The solenoid has polarity. Make sure of the correct polarity when wiring.
Gland
Gland
(70)
Door Interlock Switches
M4 Screws
Mounting Plate (supplied)
Rubber Bushing
Hinged Door
M4 Tapped Hole