DSPIC30F6010A-30I/PF Microchip Technology Inc., DSPIC30F6010A-30I/PF Datasheet - Page 77

• Manufacturer Part Number: DSPIC30F6010A-30I/PF
• Description: 16 BIT MCU/DSP 80LD 30MIPS 144 KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC30F6010A-30I/PF

• A/d Inputs: 16-Channels, 10-Bit
• Cpu Speed: 30 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 68
• Interface: CAN, I2C, SPI, UART/USART
• Ios: 68
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 80-pin TQFP
• Programmable Memory: 144K Bytes
• Ram Size: 8K Bytes
• Timers: 5-16-bit, 2-32-bit
• Voltage, Range: 2.5-5.5
• Lead Free Status / Rohs Status: RoHS Compliant part

11.0
This section describes the second 32-bit General
Purpose (GP) Timer module (Timer4/5) and associated
operational modes. Figure 11-1 depicts the simplified
block diagram of the 32-bit Timer4/5 Module.
Figure 11-2 and Figure 11-3 show Timer4/5 configured
as two independent 16-bit timers, Timer4 and Timer5,
respectively.
FIGURE 11-1:
© 2006 Microchip Technology Inc.
Note: This data sheet summarizes features of this
group of dsPIC30F devices and is not intended to be
a complete reference source. For more information
on the CPU, peripherals, register descriptions and
general device functionality, refer to the “dsPIC30F
Family Reference Manual” (DS70046).
Note:
T5IF
Event Flag
Note:
TIMER4/5 MODULE
T4CK
Timer4 is a Type B timer and Timer5 is a
Type C timer. Please refer to the appropri-
ate timer type in Section 24.0 "Electrical
Characteristics" of this document.
Data Bus<15:0>
(T4CON<6>)
Timer Configuration bit T45, T4CON(<3>) must be set to ‘
control bits are respective to the T4CON register.
Read TMR4
TGATE
Write TMR4
0
1
32-BIT TIMER4/5 BLOCK DIAGRAM
Reset
Equal
16
TMR5HLD
MSB
TMR5
PR5
Comparator x 32
16
16
TMR4
LSB
PR4
Q
Q
CK
D
Gate
Sync
T
CY
TGATE(T4CON<6>)
dsPIC30F6010A/6015
The Timer4/5 module is similar in operation to the
Timer2/3
differences, which are listed below:
• The Timer4/5 module does not support the ADC
• Timer4/5 can not be utilized by other peripheral
The operating modes of the Timer4/5 module are
determined by setting the appropriate bit(s) in the 16-bit
T4CON and T5CON SFRs.
For 32-bit timer/counter operation, Timer4 is the lsw
and Timer5 is the msw of the 32-bit timer.
Event Trigger feature
modules such as Input Capture and Output Compare
Note:
1
’ for a 32-bit timer/counter operation. All
1 x
0 1
0 0
module.
For 32-bit timer operation, T5CON control
bits are ignored. Only T4CON control bits
are used for setup and control. Timer4
clock and gate inputs are utilized for the
32-bit timer module, but an interrupt is
generated with the Timer5 Interrupt Flag
(T5IF) and the interrupt is enabled with the
Timer5 Interrupt Enable bit (T5IE).
Sync
TON
However,
TCKPS<1:0>
1, 8, 64, 256
Prescaler
2
there
DS70150B-page 75
are
some