LM317HVT Fairchild Semiconductor, LM317HVT Datasheet - Page 5

• Manufacturer Part Number: LM317HVT
• Description: Linear Regulators - Standard
• Manufacturer: Fairchild Semiconductor

Specifications of LM317HVT

• Polarity: Positive
• Number Of Outputs: 1
• Output Type: Adjustable
• Output Voltage: 1.2 V to 57 V
• Output Current: 2.2 A
• Line Regulation: 0.04 % / V
• Load Regulation: 25 mV % / V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: 0 C
• Package / Case: TO-220
• Mounting Style: Through Hole
• Reference Voltage: 1.3 V
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Application Hints
In operation, the LM117HV develops a nominal 1.25V refer-
ence voltage, V
minal. The reference voltage is impressed across program
resistor R1 and, since the voltage is constant, a constant
current I
ing an output voltage of
Since the 100 µA current from the adjustment terminal repre-
sents an error term, the LM117HV was designed to minimize
I
To do this, all quiescent operating current is returned to the
output establishing a minimum load current requirement. If
there is insufficient load on the output, the output will rise.
External Capacitors
An input bypass capacitor is recommended. A 0.1 µF disc or
1 µF solid tantalum on the input is suitable input bypassing
for almost all applications. The device is more sensitive to
the absence of input bypassing when adjustment or output
capacitors are used but the above values will eliminate the
possiblity of problems.
The adjustment terminal can be bypassed to ground on the
LM117HV to improve ripple rejection. This bypass capacitor
prevents ripple from being amplified as the output voltage is
increased. With a 10 µF bypass capacitor 80 dB ripple rejec-
tion is obtainable at any output level. Increases over 10 µF
do not appreciably improve the ripple rejection at frequen-
cies above 120 Hz. If the bypass capacitor is used, it is
sometimes necessary to include protection diodes to prevent
the capacitor from discharging through internal low current
paths and damaging the device.
In general, the best type of capacitors to use are solid tanta-
lum. Solid tantalum capacitors have low impedance even at
high frequencies. Depending upon capacitor construction, it
takes about 25 µF in aluminum electrolytic to equal 1 µF
solid tantalum at high frequencies. Ceramic capacitors are
also good at high frequencies; but some types have a large
decrease in capacitance at frequencies around 0.5 MHz. For
this reason, 0.01 µF disc may seem to work better than a 0.1
µF disc as a bypass.
Although the LM117HV is stable with no output capacitors,
like any feedback circuit, certain values of external capaci-
tance can cause excessive ringing. This occurs with values
between 500 pF and 5000 pF. A 1 µF solid tantalum (or 25 µF
aluminum electrolytic) on the output swamps this effect and
ADJ
and make it very constant with line and load changes.
1
then flows through the output set resistor R2, giv-
REF
, between the output and adjustment ter-
FIGURE 1.
DS009062-5
5
insures stability. Any increase of load capacitance larger
than 10 µF will merely improve the loop stability and output
impedance.
Load Regulation
The LM117HV is capable of providing extremely good load
regulation but a few precautions are needed to obtain maxi-
mum performance. The current set resistor connected be-
tween the adjustment terminal and the output terminal (usu-
ally 240 ) should be tied directly to the output of the
regulator rather than near the load. This eliminates line
drops from appearing effectively in series with the reference
and degrading regulation. For example, a 15V regulator with
0.05 resistance between the regulator and load will have a
load regulation due to line resistance of 0.05
resistor is connected near the load the effective line resis-
tance will be 0.05
worse.
Figure 2 shows the effect of resistance between the regula-
tor and 240
With the TO-3 package, it is easy to minimize the resistance
from the case to the set resistor, by using two separate leads
to the case. However, with the TO-5 package, care should be
taken to minimize the wire length of the output lead. The
ground of R2 can be returned near the ground of the load to
provide remote ground sensing and improve load regulation.
Protection Diodes
When external capacitors are used with any IC regulator it is
sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator. Most 10 µF capacitors have low enough
internal series resistance to deliver 20A spikes when
shorted. Although the surge is short, there is enough energy
to damage parts of the IC.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the regu-
lator, and the rate of decrease of V
discharge path is through a large junction that is able to sus-
tain 15A surge with no problem. This is not true of other
types of positive regulators. For output capacitors of 25 µF or
less, there is no need to use diodes.
The bypass capacitor on the adjustment terminal can dis-
charge through a low current junction. Discharge occurs
when either the input or output is shorted. Internal to the
LM117HV is a 50
current. No protection is needed for output voltages of 25V
FIGURE 2. Regulator with Line
set resistor.
Resistance in Output Lead
resistor which limits the peak discharge
(1 + R2/R1) or in this case, 11.5 times
IN
. In the LM117HV, this
DS009062-6
x I
www.national.com
L
. If the set