DP83934AVQB National Semiconductor, DP83934AVQB Datasheet - Page 28

• Manufacturer Part Number: DP83934AVQB
• Description: IC CTRLR ORIENT NETWORK 160PLCC
• Manufacturer: National Semiconductor

Specifications of DP83934AVQB

• Controller Type: Network Interface Controller (NIC)
• Interface: Twisted Pair
• Voltage - Supply: 4.75 V ~ 5.25 V
• Current - Supply: 140mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 160-MQFP, 160-PQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *DP83934AVQB

5 0 Buffer Management
5 4 3 Receive Descriptor Area (RDA)
After the SONIC-T buffers a packet to memory it writes 6
words of status and control information into the RDA reads
the link field to the next Receive Descriptor and writes to
the in-use field of the current descriptor In 32-bit mode the
upper word D
memory should not be used for other purposes since the
SONIC-T may still write into these locations Each Receive
Descriptor consists of the following sections (Figure 5-6)
receive status indicates status of the received packet The
SONIC-T writes the Receive Control register values into this
field Figure 5-7 shows the receive status format This field
is loaded from the contents of the Receive Control register
Note that ERR RNT BRD PRO and AMC are configura-
tion bits and are programmed during initialization See Sec-
tion 6 3 3 for the description of the Receive Control register
byte count gives the length of the complete packet from
the start of Destination Address to the end of Frame Check
Sequence (FCS)
packet pointer a 32-bit pointer that locates the packet in
the RBA The SONIC-T writes the contents of the CRBA0 1
registers into this field
sequence numbers this field displays the contents of two
8-bit counters (modulo 256) that sequence the RBAs used
and the packets buffered These counters assist the system
in determining when an RBA has been completely process-
ed The sequence numbers allow the system to tally the
packets that have been processed within a particular RBA
There are two sequence numbers that describe a packet
the RBA Sequence Number and the Packet Sequence
Number When a packet is buffered to memory the
SONIC-T maintains a single RBA Sequence Number for all
packets in an RBA and sequences the Packet Number for
succeeding packets in the RBA When the SONIC-T uses
the next RBA it increments the RBA Sequence Number and
clears the Packet Sequence Number The RBA’s sequence
counter is not incremented when the Read RRA command
is issued in the Command register The format of the Re-
ceive Sequence Numbers is shown in Figure 5-8 These
counters are reset during a SONIC-T hardware reset or by
writing zero to them
ERR
BC
15
7
LPKT
FIGURE 5-6 Receive Descriptor Format
RNT
14
6
FIGURE 5-7 Receive Status Format
k
CRS
BRD
31 16
13
5
l
COL
PRO
4
12
is not used This unused area in
CRCR
AMC
3
11
FAER
LB1
(Continued)
10
2
LB0
LBK
TL F 11719–19
9
1
PRX
MC
8
0
28
ure 5-6
receive link field a 15-bit pointer (A15– A1) that locates
the next receive descriptor The LSB of this field is the End
Of List (EOL) bit and indicates the last descriptor in the list
(Initialized by the system )
in-use field this field provides a handshake between the
system and the SONIC-T to indicate the ownership of the
descriptor When the system avails a descriptor to the
SONIC-T it writes a non-zero value into this field The
SONIC-T in turn sets this field to all ‘‘0’s’’ when it has
finished processing the descriptor (That is when the CRDA
register has advanced to the next receive descriptor ) Gen-
erally the SONIC-T releases control after writing the status
and control information into the RDA If however the SON-
IC-T has reached the last descriptor in the list it maintains
ownership of the descriptor until the system has appended
additional descriptors to the list The SONIC-T then relin-
quishes control after receiving the next packet (See Sec-
tion 5 4 6 1 for details on when the SONIC-T writes to this
field ) The receive packet descriptor format is shown in Fig-
5 4 4 Receive Buffer Management Initialization
The Receive Resource Descriptor and Buffer areas (RRA
RDA RBA) in memory and the appropriate SONIC-T regis-
ters must be properly initialized before the SONIC-T begins
buffering packets This section describes the initialization
process
5 4 4 1 Initializing The Descriptor Page
All descriptor areas (RRA RDA and TDA) used by the
SONIC-T reside within areas up to 32k (word) or 16k (long
word) pages This page may be placed anywhere within the
32-bit address range by loading the upper 16 address lines
into the UTDA URDA and URRA registers
5 4 4 2 Initializing The RRA
The initialization of the RRA consists of loading the four
SONIC-T RRA registers and writing the resource descriptor
information to memory
The RRA registers are loaded with the following values
Resource Start Area (RSA) register The RSA is loaded
with the lower 16-bit address of the beginning of the RRA
Resource End Area (REA) register The REA is loaded
with the lower 16-bit address of the end of the RRA The
end of the RRA is defined as the address of the last
RXrsrc ptr0 field in the RRA plus 4 words in 16-bit mode or 4
long words in 32-bit mode (Figure 5-4)
Resource Read Pointer (RRP) register The RRP is load-
ed with the lower 16-bit address of the first resource de-
scriptor the SONIC-T reads
Resource Write Pointer (RWP) register The RWP is load-
ed with the lower 16-bit address of the next vacant location
where a resource descriptor will be placed by the system
Note The RWP register must only point to either (1) the RXrsrc ptr0 field of
15
RBA Sequence Number
(Modulo 256)
FIGURE 5-8 Receive Sequence Number Format
one of the RRA Descriptors (2) the memory address that the RSA
points to (the start of the RRA) or (3) the memory address that the
REA points to (the end of the RRA) When the RWP
son is made it is performed after the complete RRA descriptor has
been read and not during the fetch Failure to set the RWP to any of
the above values prevents the RWP
becoming true
8
7
Packet Sequence Number
(Modulo 256)
e
RRP comparison from ever
e
RRP compari-
0